Failure-Tolerant Full-Arch Rehabilitation: A Finite Element Study Protocol and Reliability Framework for Quantifying the Mechanical Reserve That Remains After Loss of an Implant or Connection
- Paper type
- Finite element study protocol with biomedical engineering design framework
- Status
- Original Work · Working Paper
Contents
Abstract
Background. Fixed full-arch prostheses are supported by four to six implants, and systematic reviews find similar survival with fewer than five implants and with five or more. Survival statistics describe intact systems. When an implant in such a system is lost or a screw joint fails, the remaining supports carry the load, and whether they can do so depends on which support was lost, where the others are, and how the framework redistributes force. Biomechanical studies compare intact configurations. A search found no study that evaluates full-arch designs systematically across single-failure scenarios or that defines a measure of the reserve remaining after failure.
Objective. To define a residual reserve index for full-arch implant prostheses, to specify a finite element protocol for computing it across design variables and failure scenarios, and to describe its bench validation.
Framework. Borrowing contingency analysis from structural and power-system engineering, each design is evaluated intact and after removal of each support or connection in turn. Demand-to-capacity ratios for bone, implants, screws, and framework give a reserve factor in each state. The residual reserve index is the ratio of the worst single-failure reserve to the intact reserve. Progressive analysis determines whether the damaged system is stable or cascades.
Proposed methods. Parametric models of the edentulous mandible and maxilla with varied implant number, distribution, inclination, cantilever length, and framework material and section; screw joints modeled with preload and contact; loads from in vivo measurements; bench validation with instrumented implant analogs before and after removal of supports.
Central hypothesis. Residual reserve differs widely among designs with the same number of implants, depends chiefly on the position of the lost support relative to the cantilever, and is explained better by support geometry than by implant count.
Conclusions. A rigid-framework calculation illustrates the framework and suggests that loss of a distal support nearly halves reserve whereas loss of an interior support may change it little. The full protocol has not been executed, and no simulation results are reported.
Keywords: full-arch implant prosthesis; finite element analysis; structural redundancy; implant loss; load redistribution; cantilever; screw joint; reliability
1. Introduction
The number of implants needed to support a fixed full-arch prosthesis has been debated since the original protocol. A ten-year retrospective comparison of prostheses on four or six implants found a tendency toward more failures with four and similar survival overall [1]. The introduction of tilted distal implants made four the basis of a widely used concept [2], with prosthesis survival of 99.2% reported at up to ten years in the mandible [3] and long-term follow-up extending to 18 years [4]. Systematic reviews find four to six implants well documented [5], find no significant difference in survival between fewer than five and five or more implants per arch [6], and report favorable outcomes for the four-implant concept [7, 8]. A comparison of four- and six-implant immediate prostheses found no significant difference in implant survival [9]. An overview of systematic reviews summarizes the options for the edentulous maxilla [10].
These data answer the question of how often things go wrong. They do not address what happens next when something does. A prosthesis on six implants that loses one remains supported by five. A prosthesis on four that loses one is supported by three, and if the lost implant was a distal one, the cantilever on that side has lengthened by the distance to the next support. In a retrospective series of 71 arches, three prostheses were lost because of implant failures occurring after 5.8 to 11 years of function [11]. Complication reviews count such events without analyzing the mechanics that link the loss of one component to the fate of the whole [12, 13].
Engineers who design systems whose failure is costly ask a standard question: if any single element fails, does the system still carry its load? In structural engineering the property is redundancy or robustness, and measures exist to quantify the strength that remains after damage [14, 15]. In power systems the corresponding requirement is that the network withstand the loss of any one component [16]. The question is routine in those fields and has not been posed systematically for full-arch prostheses, whose biomechanical analysis has concentrated on stress in intact configurations [17, 18].
This manuscript proposes to pose it. This manuscript defines a quantity, the residual reserve index, that expresses how much of a design’s mechanical margin survives the worst single failure; specifies a finite element protocol to compute it; and outlines its validation. It also considers whether prostheses could be designed to tolerate failure, as distinct from merely having more implants. The premise that more implants mean more safety is examined, not assumed: an additional implant placed where it does not shorten the load path after a failure may add little.
2. Background and Current Scientific Evidence
Load distribution in implant-supported prostheses
The analytical basis was laid early. The distribution of a load applied to a fixed prosthesis depends on the number, arrangement, and stiffness of the implants and on the form and stiffness of the prosthesis; a stiff prosthesis distributes load among its supports, and cantilever extensions create a lever that amplifies force on the nearest implant and loads distant ones in tension [19]. Design rules derived from lever mechanics were proposed for clinical use [20], and the ratio of anteroposterior implant spread to cantilever length became a planning heuristic [21]. In vivo measurements with instrumented abutments confirmed that implants supporting fixed prostheses experience both axial forces and bending moments whose distribution depends on load position [22]. Reviews relate functional forces to the biomechanics of implant-supported prostheses [23].
Finite element studies of full-arch configurations
Finite element analysis has been used to compare tilted implants with cantilevers [24, 25], to analyze immediately loaded four-implant configurations, in which a 200-N load at the cantilever raised peak bone strains substantially compared with loading at the distal abutment [26], and to compare three-, four-, and five-implant immediate-loading designs, with the five-implant design showing better stress and strain control [27]. Arch form and cantilever length have been varied in four-implant models [28]. Framework material and architecture, including polymer frameworks and lattice designs, have been examined [29, 30]. These studies analyze the intact prosthesis. A general web search during preparation of this manuscript surfaced one finite element analysis of rescue configurations after posterior implant loss in a four-implant rehabilitation; it could not be located in PubMed, its venue was not verified, and it is not cited. Rescue analysis asks how to repair. The present question is how much margin remains before repair, across all possible single failures, as a property of the original design.
Modes of failure
Supports are lost in several ways with different mechanical consequences. An implant may lose osseointegration and cease to carry load. A prosthetic or abutment screw may loosen, leaving a connection that can transmit compression through contact but little tension or moment, or may fracture [31, 32]. The framework may fracture, dividing the structure. Veneering material may fracture without affecting load paths. Misfit between framework and implants alters the initial state of the screw joints [33]. Technical complications of each kind are frequent in long-term follow-up [12, 13, 34, 35].
Credibility of finite element models
Finite element results depend on geometry, material assignments, interface conditions, loads, and mesh, and the dental literature has been criticized for weak verification and validation [18]. Guidance on extracting clinically relevant information from simulations and on verification, validation, and sensitivity analysis is available [36, 37], and a standard framework exists for assessing model credibility in medical device contexts [38]. Bone tissue properties have been measured, with Young’s moduli of roughly 15 GPa for trabecular tissue and 19 to 21 GPa for cortical microspecimens in one widely cited study [39]; apparent-level properties for jaw bone depend on density and must be assigned from primary sources. The mandible itself deforms under function [40], which matters for a rigid cross-arch prosthesis.
Redundancy concepts from engineering
Structural redundancy is quantified by comparing the capacity of the damaged structure with that of the intact one, and reliability-based measures weigh the probability and consequence of member loss [14]. Robustness assessment distinguishes direct consequences of a failure from indirect consequences that follow from the system’s response [15]. Contingency analysis in power systems evaluates the network after the outage of each single element [16]. These ideas transfer directly. A full-arch prosthesis is a small, statically indeterminate structure on a handful of supports, and exhaustive enumeration of single and double failures is computationally trivial compared with the systems for which the methods were developed.
Summary
It is established that load distribution depends on support geometry and framework stiffness, that cantilevers amplify load, and that four to six implants give similar survival of intact prostheses. Finite element comparisons of intact designs are numerous. No systematic evaluation of post-failure reserve as a design property was identified.
3. Research Gap
Four things are missing. A definition of mechanical reserve after component loss for full-arch prostheses. A protocol for computing it that treats screw-joint failure as well as implant loss. Knowledge of how it varies with implant number, distribution, cantilever, and framework design. And any test of whether it relates to what happens clinically after an implant is lost.
PubMed searches combining full-arch terms and finite element analysis with implant loss or failure, and combining full-arch terms with redundancy, fail-safe, damage tolerance, or robustness, each returned no records (Appendix A).
4. Research Objective and Central Hypothesis
The objective is to develop and validate a method for quantifying the residual mechanical reserve of full-arch implant-supported prostheses after single-component failure, and to use it to compare designs.
The central hypothesis is that, across a parametric design space, (a) the residual reserve index varies substantially among designs with the same number of implants; (b) the loss of a distal support adjacent to a cantilever reduces reserve far more than the loss of an interior support; and (c) geometric descriptors of the support layout, in particular the post-failure cantilever-to-spread ratio, explain more of the variance in residual reserve than the number of implants does.
A secondary hypothesis is that designs can be identified in which every single failure leaves the system above a stated reserve threshold under functional loading, and that such designs are not simply those with the most implants.
The central hypothesis is refuted if implant count alone predicts residual reserve as well as geometric descriptors do, or if residual reserve is nearly uniform across designs.
5. Scientific and Theoretical Framework
States, demands, and capacities
A design d is specified by implant positions, inclinations, and dimensions; framework geometry and material; connection type; and cantilever lengths. A state s is the intact configuration (s=0) or a configuration with one or more components failed. A load case j is an occlusal load of specified magnitude, direction, and location. For each component c (the bone around each implant, each implant body, each screw, each framework section), the model returns a demand q_c,j^(s): peak bone strain, implant stress, screw tensile and bending load relative to preload, or framework stress. Each has a capacity Q_c: a strain limit for bone, yield or fatigue limits for metal components, and joint-opening or yield limits for screws. The utilization is
u_c,j^(s)=(q_c,j^(s))/Q_c (1)
and the reserve factor of the design in state s is the load multiplier at which the most utilized component reaches its capacity:
RF^((s))=1/(maxc,j u_c,j^(s)) (2)
for linear response; for non-linear contact and preload behavior it is found by load stepping.
Residual reserve index
Let S_1 be the set of single-failure states. The residual reserve index is
RRI=(mins∈S_1RF^((s)))/(RF^((0))) (3)
the fraction of intact reserve that survives the worst single failure. A probability-weighted mean over S_1 is reported alongside it where failure probabilities by position can be justified, and with equal weights otherwise. The absolute post-failure reserve, min_sRF^((s)), is reported as well, because a design with high intact reserve and modest RRI may still be safer after failure than one with low intact reserve and high RRI. A design is termed single-failure tolerant at load level Λ if RF^((s))≥Λ for every s∈S_1, with Λ=1 under functional loads as the minimum criterion.
Failure states
Four classes of single failure are modeled (Table 1). They differ in what the failed component can still transmit, which is why implant count alone is an incomplete descriptor.
| Failure | Mechanical effect | Model representation |
|---|---|---|
| Loss of osseointegration of implant i | Support removed | Implant–bone interface of implant i released; implant remains attached to framework as mass only |
| Loss of preload at screw joint i | Connection transmits compression by contact; no tension or moment until gap closes | Preload set to zero; frictional contact retained |
| Screw or abutment fracture at joint i | Connection lost; framework may bear on abutment in compression | Fastener removed; contact retained |
| Framework fracture between supports i and i+1 | Structure divided into two segments | Section released at the fracture plane |
Progressive analysis
After a first failure, demands on the remaining components rise. If any exceeds its capacity under functional load, that component is failed in turn and the analysis repeated, as in progressive-collapse assessment [15]. The sequence ends in one of two ways: a damaged but stable state, or loss of support for the prosthesis. The number of steps and the final state are recorded. A design in which a single implant loss leads by cascade to prosthesis failure under ordinary function is fragile whatever its implant count.
Fatigue adds a time dimension. A redistributed cyclic demand below static capacity may still shorten the life of screws and framework. With a stress–life relation of the form N∝σ^(−b), a rise in cyclic stress by a factor ϕ shortens life by ϕ^(−b). The exponent depends on material and detail and must be taken from fatigue data for the specific components; it is not asserted here.
6. Methodology
Geometry
Jaws. Edentulous mandible and maxilla reconstructed from computed tomography of representative anatomy, in three arch forms (square, ovoid, tapered) as used in prior work [28], with cortical thickness and cancellous density varied at two levels.
Implant configurations. Four implants with tilted distal fixtures; four axial implants; five and six implants in even and uneven distributions, including layouts that pair two implants at each distal end; all with standardized implant dimensions and a common connection design. Positions are parameterized by arc-length coordinates along the ridge so that distributions can be varied continuously.
Prostheses. Screw-retained one-piece frameworks in titanium alloy, cobalt–chromium, zirconia, and a high-performance polymer [29], with two cross-sectional depths and cantilever lengths from zero to a clinically used maximum.
Materials and interfaces
Linear elastic, isotropic properties for metals and ceramics from manufacturers’ data and standards; transversely isotropic or density-dependent properties for bone from primary experimental sources, with the range of published values carried into the sensitivity analysis [39]. No bone property values are fixed in this protocol beyond citing that source for tissue-level moduli. Osseointegrated interfaces are bonded. Screw joints are modeled explicitly, with pretension applied to the screw shank to the manufacturer’s recommended preload and frictional contact at the mating surfaces [31], so that joint opening and loss of clamping can occur. A subset of models includes an initial vertical misfit at one joint [33].
Loads and constraints
Load cases: bilateral posterior, unilateral molar, unilateral at the cantilever tip, and anterior incisal, vertical and at an oblique angle. Magnitudes are taken from in vivo measurements on implant-supported fixed prostheses [22] for functional loading and scaled upward for a parafunctional case; a 200-N cantilever load allows comparison with a published model [26]. The mandible is constrained at the condyles and loaded through muscle force vectors in a subset to capture jaw flexure [40]; the remaining models use a simpler constraint, and the difference is reported.
Capacities
Bone: a strain limit for cortical bone taken from the mechanobiological and fatigue literature, treated as uncertain and varied. Implants and frameworks: yield strength and, for cyclic assessment, endurance limits from material data and from component tests of the kind specified in the dynamic loading standard for dental implants [41]. Screws: the load at which the joint opens and the load at which the screw yields, both computed from the preload model [32, 42]. Because RRI is a ratio, it is less sensitive to the absolute capacities than the reserve factors are, provided the governing component is the same in the intact and damaged states; where the governing component changes, the dependence is examined.
Verification and sensitivity
Mesh convergence is established for each output with reported discretization error. Solver settings for contact and preload are verified on a single preloaded joint against the analytic joint diagram. A global sensitivity analysis over bone properties, friction coefficient, preload, load direction, and capacity limits identifies which uncertainties move RRI and the design ranking. Credibility assessment follows ASME V&V 40, with the context of use defined as comparative ranking of designs [36–38].
Bench validation
Specimens. Polymer jaw analogs with material properties chosen to approximate the stiffness of bone, carrying implant analogs in three of the simulated configurations; frameworks manufactured from the simulated designs.
Instrumentation. Strain gauges on each abutment calibrated to report axial force and two bending moments, following established instrumented-abutment methods [22]; strain gauges on the framework at sections predicted to be critical; displacement transducers at the cantilever tip.
Procedure. Each specimen is loaded in a testing machine at the simulated load points in the intact state. A support is then disabled, by unscrewing the prosthetic screw (preload loss), by removing the screw (fastener loss), or by releasing the analog from the jaw (loss of integration), and the loading repeated. Each of the single-failure states is tested in turn.
Comparison. Measured and predicted implant reactions, framework strains, and tip displacements are compared for intact and damaged states. The validation metric is the error in the predicted change in the maximum implant reaction from intact to damaged state, since that change is what RRI depends on. Acceptance limits are prespecified.
Fatigue check. For one configuration, cyclic loading at the functional load level is applied in the worst single-failure state to a specified number of cycles or to failure, to test whether the component predicted to govern is the one that fails.
Design-space analysis
The validated model is run over the full factorial of design variables in intact and all single-failure states. Outputs for each design: RF^((0)), RRI, the identity of the critical failure and of the governing component, and cascade depth. The central hypothesis is tested by comparing regression models for RRI on implant count alone and on geometric descriptors: intact and post-failure cantilever-to-spread ratios, distance from the distal implant to its neighbor, and framework bending stiffness. The contrast between distal and interior support loss is tested directly within designs. Designs meeting the single-failure tolerance criterion are identified, and their common features described.
Exploratory clinical comparison
Published and institutional cohorts of full-arch prostheses in which an implant was lost are examined for whether the prosthesis survived, was modified, or was lost [11]. Where the configuration is documented, the model’s prediction for that failure is compared with the outcome. Numbers will be small and selection strong; this is a plausibility check.
Reproducibility
Geometry files, meshes, material tables with sources, input decks, and post-processing scripts are to be deposited, together with bench data. Without them the index cannot be recomputed.
Ethics
The computational and bench work involves no human participants beyond the use of de-identified imaging for geometry, for which institutional approval or exemption is required. The exploratory clinical comparison uses published or de-identified records under appropriate approval.
7. Analytical Development
A rigid-framework model
Before any finite element computation, a closed-form model shows the structure of the problem. Unroll the arch to a line and treat the framework as rigid on n implants of equal axial stiffness at positions x_1,…,x_n. A vertical load P at position x_P produces implant reactions
F_i=P(1/n+((x_P−x)(x_i−x))/(∑_k^ (x_k−x)^2)) (4)
with x the centroid of the implant positions. This is the standard result for a rigid body on a group of elastic supports and corresponds to the analysis in the early biomechanical literature [19]. A negative F_i is tension. The model ignores framework flexibility, the curvature of the arch, bending moments in the implants, and joint behavior. Its purpose is to expose how the reactions change when a support is removed.
Illustration
Table 2 applies equation (4) to four and to six evenly spaced implants over the same 30-mm span, with the load at the tip of a 10-mm cantilever. The figures are arithmetic on the formula for an idealized layout. They are not finite element results and are not predictions for any clinical configuration.
| Configuration | Implant positions | Largest compressive reaction | Largest tensile reaction | Ratio of intact to damaged peak reaction |
|---|---|---|---|---|
| Four implants, intact | 0, 10, 20, 30 | 1.00 | 0.50 | — |
| Four implants, distal lost | 0, 10, 20 | 1.83 | 1.17 | 0.55 |
| Four implants, interior lost | 0, 20, 30 | 1.00 | 0.50 | 1.00 |
| Six implants, intact | 0, 6, 12, 18, 24, 30 | 0.76 | 0.43 | — |
| Six implants, distal lost | 0, 6, 12, 18, 24 | 1.13 | 0.73 | 0.67 |
Three points emerge. Loss of the distal implant next to the loaded cantilever raises the peak reaction by 83% with four implants and by 49% with six, and more than doubles the tensile reaction on the far implant in the four-implant case. Loss of an interior implant leaves the peak reactions unchanged in this rigid idealization, because the extreme supports and the lever arm are unaltered; in a flexible framework the unsupported span would raise framework bending, which is why the finite element model is needed. And the benefit of six implants over four after distal loss, a ratio of 0.67 against 0.55, comes from the shorter distance to the next support, since the new cantilever is 16 mm instead of 20 mm. The number of implants matters through where they are.
Post-failure cantilever as the governing descriptor
For a load at the cantilever tip, equation (4) gives the reaction at the distal implant as a function of the cantilever length a and the layout. After loss of the distal implant, the cantilever becomes a+g, where g is the gap to the next implant. The damaged-state peak reaction grows approximately linearly with (a+g) relative to the spread of the remaining implants. The quantity
χ=(a+g)/(L−g) (5)
where L is the original spread between the most anterior and most distal supports on the unrolled line, is the post-failure cantilever-to-spread ratio. It can be reduced by shortening the cantilever, by placing a second implant close to the distal one so that g is small, or by extending the spread. Adding an implant in the anterior segment, which increases the count without changing a, g, or L, leaves χ unchanged. This is the formal basis for hypothesis (c) and for the suggestion that paired distal implants may confer more failure tolerance than the same number evenly spaced. Whether the effect survives framework flexibility and realistic arch geometry is what the finite element analysis is to determine.
Controlled shortening as a designed fallback
Suppose that after loss of the distal implant the prosthesis is shortened so that no load can be applied beyond the new distal implant at 20 mm. In the four-implant example the peak reaction for a load at that implant is, by equation (4), 0.83 P, below the intact value of 1.00 P at the original cantilever tip. Reserve is restored at the cost of occlusal table. A prosthesis designed with a predetermined sectioning plane distal to each implant, so that the cantilever can be removed cleanly without compromising the remaining framework, would embody this fallback. The observation motivates the engineering concepts in Appendix D and is offered as an idea to be tested.
What the rigid model cannot show
Loss of preload at a screw joint is not loss of the support: the joint still carries compression. Under a cantilever load the distal joint is in compression and may function almost normally without preload, whereas the far joints, in tension, open. The reverse holds for anterior loads. The consequence of a loose screw therefore depends on its position relative to the load in a way that requires contact modeling. Framework flexibility shifts load toward the supports nearest the load and makes interior supports matter. Mandibular flexure adds self-equilibrated forces in a rigid cross-arch framework. These are the phenomena for which the finite element protocol is specified, and the rigid model’s conclusions should be regarded as hypotheses for it to test.
8. Discussion
The proposal moves the biomechanical assessment of full-arch prostheses from the intact state to the damaged state and gives the result a number. The idea is elementary in other branches of engineering. Its absence from implant prosthodontics probably reflects the reassuring survival statistics for intact prostheses and the difficulty of studying rare failures clinically. Simulation is well suited to rare events, since every failure can be imposed at will.
The illustrative calculation already challenges two intuitions. One is that all implant losses are alike. In the idealized model, losing an interior implant changes little and losing a distal one nearly halves reserve. If the finite element analysis confirms a large asymmetry, clinical attention after implant loss should depend strongly on position, and so should planning: the distal implants are the ones whose loss the design must be able to tolerate. The other intuition is that implant count measures safety. The calculation suggests that count matters through geometry, and that an added implant earns its place only if it shortens the post-failure cantilever or stiffens the path around a lost support.
A further consideration is what the index should be compared against. Clinicians already hold informal rules that encode some of this reasoning: keep cantilevers short relative to implant spread, avoid relying on a single distal implant in poor bone, add an implant when in doubt. The index is useful only if it distinguishes designs that these rules treat alike, or contradicts them in cases that can be checked. The design-space analysis therefore reports, for each rule of thumb, how much of the variance in residual reserve it captures, so that the incremental value of computing the index is stated and not assumed.
The framework has substantial limitations. Capacities are uncertain, especially for bone, where a single strain limit is a crude representation of a tissue that adapts and fatigues. RRI mitigates this by being a ratio, and the mitigation fails when the governing component changes between states. Implant loss is not instantaneous; a failing implant sheds load gradually, and the bone around the others may adapt. A static contingency analysis ignores time. Clinical failure often involves biology, with peri-implantitis affecting several implants, which violates the assumption of independent single failures; double-failure states of adjacent implants should be included for that reason.
The finite element model itself can mislead. Bonded interfaces overstate support. Preloaded contact is numerically delicate. Bone properties vary between patients more than any design variable changes the result. The protocol’s emphasis on comparative ranking, bench validation of the change in reactions, and sensitivity analysis is meant to confine conclusions to what the model can support. A ranking that is not robust to plausible variation in bone properties is not a finding.
There is a tension between failure tolerance and other design goals. More implants and paired distal implants mean more surgery, more cost, and more sites for biological complications, and available bone often dictates the layout. Shorter cantilevers reduce the occlusal table. The index does not resolve these trade-offs. It makes one side of them visible.
The exploratory clinical comparison is weak evidence at best. Prostheses that survive an implant loss do so partly because clinicians intervene, and those that are lost may have had other problems. A registry that recorded configuration, the position of each lost implant, and the subsequent course would be needed for real validation.
9. Clinical Significance
If validated, the index would support three kinds of decision. At planning, alternative layouts could be compared for what they leave after the loss of each implant, alongside conventional criteria, and the case for a fifth or sixth implant in a particular position could be stated quantitatively. At design, cantilever length could be set with reference to the post-failure state, and frameworks could incorporate features that allow controlled shortening. After an implant is lost, the clinician could consult the computed reserve for that specific loss to judge whether the prosthesis can remain in function while a replacement is arranged, should be shortened immediately, or must be removed.
The work also bears on how risk is communicated. A patient choosing between four and six implants could be told what each offers if one implant fails, in addition to the survival of intact prostheses.
These applications require the simulations, bench tests, and clinical corroboration described. None exists yet.
10. Limitations
No simulation has been run; the only numbers presented come from a rigid one-dimensional idealization. Capacities, especially for bone, are uncertain. The analysis is static, with fatigue treated by a generic scaling. Failures are assumed sudden and, for single-failure analysis, independent. Bonded interfaces and idealized material properties limit absolute accuracy. Bench analogs do not reproduce bone. The design space, though broad, cannot cover every implant system and connection. Clinical corroboration is exploratory. The literature was assessed from abstracts and index records. One relevant finite element study surfaced by web search could not be verified and was not cited. The patent review did not include a professional search.
11. Future Validation
After the computational and bench stages, three steps would strengthen the work. Cadaveric or large-animal validation with implants in bone would test the interface assumptions. A multicenter registry of implant losses in full-arch prostheses, recording configuration and subsequent course, would allow the index to be tested as a predictor of prosthesis survival after loss. And prototype failure-tolerant frameworks, with planned sectioning planes or paired distal supports, would be tested in fatigue in intact and damaged states against conventional designs. Independent groups should recompute the index from the deposited models.
12. Conclusion
Whether a full-arch implant prosthesis can lose a support and continue to function safely is a property of its design that current evidence and current planning do not address. A residual reserve index, computed by solving the design intact and after each single failure, quantifies that property. A simple rigid-framework calculation indicates that the position of the lost implant relative to the cantilever, and the distance to the next support, govern the outcome more than the number of implants. The finite element protocol and bench validation described would test this and identify designs that tolerate failure. Until they are carried out, the index is a defined but unevaluated quantity.
Cite this paper
Jain S, Gupta A. Failure-Tolerant Full-Arch Rehabilitation: A Finite Element Study Protocol and Reliability Framework for Quantifying the Mechanical Reserve That Remains After Loss of an Implant or Connection. Working paper. Center for Implant Dentistry; 2026. Available from: https://bayareaimplantdentistry.com/clinician-research-and-publications/failure-tolerant-full-arch-rehabilitation
References
- Brånemark PI, Svensson B, van Steenberghe D. Ten-year survival rates of fixed prostheses on four or six implants ad modum Brånemark in full edentulism. Clin Oral Implants Res. 1995;6(4):227-31. doi:10.1034/j.1600-0501.1995.060405.x (opens in a new tab). PMID: 8603114 (opens in a new tab).
- Maló P, Rangert B, Nobre M. “All-on-Four” immediate-function concept with Brånemark System implants for completely edentulous mandibles: a retrospective clinical study. Clin Implant Dent Relat Res. 2003;5 Suppl 1:2-9. doi:10.1111/j.1708-8208.2003.tb00010.x (opens in a new tab). PMID: 12691645 (opens in a new tab).
- Malo P, de Araújo Nobre M, Lopes A, Moss SM, Molina GJ. A longitudinal study of the survival of All-on-4 implants in the mandible with up to 10 years of follow-up. J Am Dent Assoc. 2011;142(3):310-20. doi:10.14219/jada.archive.2011.0170 (opens in a new tab). PMID: 21357865 (opens in a new tab).
- Maló P, de Araújo Nobre M, Lopes A, Ferro A, Botto J. The All-on-4 treatment concept for the rehabilitation of the completely edentulous mandible: A longitudinal study with 10 to 18 years of follow-up. Clin Implant Dent Relat Res. 2019;21(4):565-577. doi:10.1111/cid.12769 (opens in a new tab). PMID: 30924309 (opens in a new tab).
- Heydecke G, Zwahlen M, Nicol A, Nisand D, Payer M, Renouard F, et al. What is the optimal number of implants for fixed reconstructions: a systematic review. Clin Oral Implants Res. 2012;23 Suppl 6:217-28. doi:10.1111/j.1600-0501.2012.02548.x (opens in a new tab). PMID: 23062144 (opens in a new tab).
- Daudt Polido W, Aghaloo T, Emmett TW, Taylor TD, Morton D. Number of implants placed for complete-arch fixed prostheses: A systematic review and meta-analysis. Clin Oral Implants Res. 2018;29 Suppl 16:154-183. doi:10.1111/clr.13312 (opens in a new tab). PMID: 30328199 (opens in a new tab).
- Patzelt SB, Bahat O, Reynolds MA, Strub JR. The all-on-four treatment concept: a systematic review. Clin Implant Dent Relat Res. 2014;16(6):836-55. doi:10.1111/cid.12068 (opens in a new tab). PMID: 23560986 (opens in a new tab).
- Soto-Penaloza D, Zaragozí-Alonso R, Penarrocha-Diago M, Penarrocha-Diago M. The all-on-four treatment concept: Systematic review. J Clin Exp Dent. 2017;9(3):e474-e488. doi:10.4317/jced.53613 (opens in a new tab). PMID: 28298995 (opens in a new tab).
- Zhang Y, Li S, Di P, Zhang Y, Wu A, Lin Y. Comparison of 4- or 6-implant supported immediate full-arch fixed prostheses: A retrospective cohort study of 217 patients followed up for 3-13 years. Clin Implant Dent Relat Res. 2023;25(2):381-397. doi:10.1111/cid.13170 (opens in a new tab). PMID: 36522852 (opens in a new tab).
- Messias A, Nicolau P, Guerra F. Different Interventions for Rehabilitation of the Edentulous Maxilla with Implant-Supported Prostheses: An Overview of Systematic Reviews. Int J Prosthodont. 2021;34:s63-s84. doi:10.11607/ijp.7162 (opens in a new tab). PMID: 33571327 (opens in a new tab).
- Papaspyridakos P, Bordin TB, Kim YJ, El-Rafie K, Pagni SE, Natto ZS, et al. Technical Complications and Prosthesis Survival Rates with Implant-Supported Fixed Complete Dental Prostheses: A Retrospective Study with 1- to 12-Year Follow-Up. J Prosthodont. 2020;29(1):3-11. doi:10.1111/jopr.13119 (opens in a new tab). PMID: 31650669 (opens in a new tab).
- Papaspyridakos P, Chen CJ, Chuang SK, Weber HP, Gallucci GO. A systematic review of biologic and technical complications with fixed implant rehabilitations for edentulous patients. Int J Oral Maxillofac Implants. 2012;27(1):102-10. PMID: 22299086 (opens in a new tab).
- Bozini T, Petridis H, Garefis K, Garefis P. A meta-analysis of prosthodontic complication rates of implant-supported fixed dental prostheses in edentulous patients after an observation period of at least 5 years. Int J Oral Maxillofac Implants. 2011;26(2):304-18. PMID: 21483883 (opens in a new tab).
- Frangopol DM, Curley JP. Effects of Damage and Redundancy on Structural Reliability. J. Struct. Eng.. 1987;113(7):1533-1549. doi:10.1061/(asce)0733-9445(1987)113:7(1533) (opens in a new tab).
- Baker JW, Schubert M, Faber MH. On the assessment of robustness. Structural Safety. 2008;30(3):253-267. doi:10.1016/j.strusafe.2006.11.004 (opens in a new tab).
- Billinton R, Allan RN. Reliability evaluation of power systems. 2nd ed. New York: Plenum Press; 1996.
- Geng JP, Tan KB, Liu GR. Application of finite element analysis in implant dentistry: a review of the literature. J Prosthet Dent. 2001;85(6):585-98. doi:10.1067/mpr.2001.115251 (opens in a new tab). PMID: 11404759 (opens in a new tab).
- Falcinelli C, Valente F, Vasta M, Traini T. Finite element analysis in implant dentistry: State of the art and future directions. Dent Mater. 2023;39(6):539-556. doi:10.1016/j.dental.2023.04.002 (opens in a new tab). PMID: 37080880 (opens in a new tab).
- Skalak R. Biomechanical considerations in osseointegrated prostheses. J Prosthet Dent. 1983;49(6):843-8. doi:10.1016/0022-3913(83)90361-x (opens in a new tab). PMID: 6576140 (opens in a new tab).
- Rangert B, Jemt T, Jörneus L. Forces and moments on Branemark implants. Int J Oral Maxillofac Implants. 1989;4(3):241-7. PMID: 2700747 (opens in a new tab).
- English CE. Critical A-P spread. Implant Soc. 1990;1(1):2-3. PMID: 2073515 (opens in a new tab).
- Duyck J, Van Oosterwyck H, Vander Sloten J, De Cooman M, Puers R, Naert I. Magnitude and distribution of occlusal forces on oral implants supporting fixed prostheses: an in vivo study. Clin Oral Implants Res. 2000;11(5):465-75. doi:10.1034/j.1600-0501.2000.011005465.x (opens in a new tab). PMID: 11168239 (opens in a new tab).
- Sahin S, Cehreli MC, Yalçin E. The influence of functional forces on the biomechanics of implant-supported prostheses–a review. J Dent. 2002;30(7-8):271-82. doi:10.1016/s0300-5712(02)00065-9 (opens in a new tab). PMID: 12554107 (opens in a new tab).
- Zampelis A, Rangert B, Heijl L. Tilting of splinted implants for improved prosthodontic support: a two-dimensional finite element analysis. J Prosthet Dent. 2007;97(6 Suppl):S35-43. doi:10.1016/S0022-3913(07)60006-7 (opens in a new tab). PMID: 17618932 (opens in a new tab).
- Bevilacqua M, Tealdo T, Menini M, Pera F, Mossolov A, Drago C, et al. The influence of cantilever length and implant inclination on stress distribution in maxillary implant-supported fixed dentures. J Prosthet Dent. 2011;105(1):5-13. doi:10.1016/S0022-3913(10)60182-5 (opens in a new tab). PMID: 21194582 (opens in a new tab).
- Horita S, Sugiura T, Yamamoto K, Murakami K, Imai Y, Kirita T. Biomechanical analysis of immediately loaded implants according to the “All-on-Four” concept. J Prosthodont Res. 2017;61(2):123-132. doi:10.1016/j.jpor.2016.08.002 (opens in a new tab). PMID: 27615425 (opens in a new tab).
- Baki N, Avcu GY, Tuzlali M. Biomechanical evaluation of three full-arch immediate loading protocols in the mandible via finite element analysis: All-on-4, Trefoil, and Five-implant design. BMC Oral Health. 2025;25(1):1995. doi:10.1186/s12903-025-07404-1 (opens in a new tab). PMID: 41299501 (opens in a new tab).
- Ok Bostan H, Yeşil Z. Biomechanical evaluation of cantilever length and arch form in the All-on-4 implant concept: a finite element analysis. BMC Oral Health. 2026;26(1). doi:10.1186/s12903-026-08726-4 (opens in a new tab). PMID: 42216196 (opens in a new tab).
- Villefort RF, Diamantino PJS, Zeidler SLVV, Borges ALS, Silva-Concílio LR, Saavedra GDFA, et al. Mechanical Response of PEKK and PEEK As Frameworks for Implant-Supported Full-Arch Fixed Dental Prosthesis: 3D Finite Element Analysis. Eur J Dent. 2022;16(1):115-121. doi:10.1055/s-0041-1731833 (opens in a new tab). PMID: 34560810 (opens in a new tab).
- Yiğit E, Özcan N, Şahin V. Effect of framework material and gyroid lattice design on the biomechanics of all-on-four full-arch prostheses. BMC Oral Health. 2026;26(1). doi:10.1186/s12903-026-08484-3 (opens in a new tab). PMID: 42057071 (opens in a new tab).
- Jörnéus L, Jemt T, Carlsson L. Loads and designs of screw joints for single crowns supported by osseointegrated implants. Int J Oral Maxillofac Implants. 1992;7(3):353-9. PMID: 1289261 (opens in a new tab).
- McGlumphy EA, Mendel DA, Holloway JA. Implant screw mechanics. Dent Clin North Am. 1998;42(1):71-89. PMID: 9421671 (opens in a new tab).
- Katsoulis J, Takeichi T, Sol Gaviria A, Peter L, Katsoulis K. Misfit of implant prostheses and its impact on clinical outcomes. Definition, assessment and a systematic review of the literature. Eur J Oral Implantol. 2017;10 Suppl 1:121-138. PMID: 28944373 (opens in a new tab).
- Jemt T. Failures and complications in 391 consecutively inserted fixed prostheses supported by Brånemark implants in edentulous jaws: a study of treatment from the time of prosthesis placement to the first annual checkup. Int J Oral Maxillofac Implants. 1991;6(3):270-6. PMID: 1813395 (opens in a new tab).
- Pelser D, Schepers M, Abou-Ayash S, Bjelopavlovic M, Bremer MK, Grander L, et al. Technical and biological complications of implant-supported fixed complete dentures: a retrospective cohort study with up to 17 years of follow-up. Int J Implant Dent. 2026;12(1). doi:10.1186/s40729-026-00689-z (opens in a new tab). PMID: 42129020 (opens in a new tab).
- Viceconti M, Olsen S, Nolte LP, Burton K. Extracting clinically relevant data from finite element simulations. Clin Biomech (Bristol). 2005;20(5):451-4. doi:10.1016/j.clinbiomech.2005.01.010 (opens in a new tab). PMID: 15836931 (opens in a new tab).
- Anderson AE, Ellis BJ, Weiss JA. Verification, validation and sensitivity studies in computational biomechanics. Comput Methods Biomech Biomed Engin. 2007;10(3):171-84. doi:10.1080/10255840601160484 (opens in a new tab). PMID: 17558646 (opens in a new tab).
- American Society of Mechanical Engineers. Assessing credibility of computational modeling through verification and validation: application to medical devices. ASME V&V 40-2018. New York: ASME; 2018.
- Rho JY, Ashman RB, Turner CH. Young’s modulus of trabecular and cortical bone material: ultrasonic and microtensile measurements. J Biomech. 1993;26(2):111-9. doi:10.1016/0021-9290(93)90042-d (opens in a new tab). PMID: 8429054 (opens in a new tab).
- Korioth TW, Hannam AG. Deformation of the human mandible during simulated tooth clenching. J Dent Res. 1994;73(1):56-66. doi:10.1177/00220345940730010801 (opens in a new tab). PMID: 8294619 (opens in a new tab).
- International Organization for Standardization. ISO 14801:2016. Dentistry—Implants—Dynamic loading test for endosseous dental implants. Geneva: ISO; 2016.
- Bickford JH. An introduction to the design and behavior of bolted joints. 3rd ed. New York: Marcel Dekker; 1995.
- Astra Tech Inc, applicant. Method and system for designing custom restorations for dental implants. European patent application EP 1 973 491 A1. Priority 2006 Jan 5; published 2008 Oct 1 (related CN 101400317 A).
- Dentsply Sirona Inc, applicant. Method, system and devices for instant automated design of a customized dental object. United States patent application publication US 2022/0296344 A1. Priority 2019 Sep 5; published 2022 Sep 22 (granted as US 12,465,469 B2; related WO 2021/046147 A1).
- U.S. Food and Drug Administration. Product classifications: endosseous dental implant, 21 CFR 872.3640 (product code DZE); endosseous dental implant abutment, 21 CFR 872.3630 (product code NHA). Silver Spring (MD): FDA.

