Skip to main content

Sleep-Related Mechanical Loading and Early Implant Healing: A Prospective, Time-Resolved, Instrumentally Assessed Cohort Protocol for Nocturnal Bruxism

Paper type
Prospective clinical research protocol (observational cohort with instrument validation substudies)
Status
Original Work · Working Paper
Contents
  1. 1Introduction
  2. 2Background and Current Scientific Evidence
  3. 3Research Gap
  4. 4Research Objective and Central Hypothesis
  5. 5Scientific and Theoretical Framework
  6. 6Methodology
  7. 7Analytical Development
  8. 8Discussion
  9. 9Clinical Significance
  10. 10Limitations
  11. 11Future Validation
  12. 12Conclusion

Abstract

Background. Bruxism is widely regarded as a risk factor for implant failure. Meta-analyses report risk ratios and odds ratios between about 2 and 5. Nearly all of the underlying studies classified bruxism by self-report or clinical signs, which correspond to “possible” or “probable” bruxism in the international grading. The one prospective study identified that set out to use electromyography reported insufficient recruitment and failed recordings. No study has related objectively measured sleep-time jaw-muscle activity during healing to implant outcomes, and none has considered the temporal structure of that activity.

Objective. To specify a feasible prospective cohort in which sleep bruxism is measured instrumentally over multiple nights during the healing period and related to the trajectory of implant stability, with the loading status of the implant used to test specificity.

Design. Adults receiving posterior implants are followed in two strata: implants provisionalized in occlusion during healing, and implants left unloaded. Ambulatory masseter electromyography with heart-rate recording is obtained for five consecutive nights in each of three blocks, with polysomnographic calibration in a subsample. Exposure metrics include episode index, duration, amplitude, clustering, and a force-weighted nightly load estimate scaled by the implant’s share of occlusal contact. The primary outcome is gain in implant stability quotient from week 2 to week 12.

Analysis. Mixed models test the association between nocturnal load metrics and stability gain and its interaction with loading stratum. Self-reported bruxism is analyzed in parallel to quantify misclassification.

Central hypothesis. The nightly number of high-amplitude, long-duration masseter episodes, and not self-reported bruxism status, is associated with reduced stability gain in loaded implants and is not associated with it in unloaded implants.

Conclusions. The question is established, and the evidence is weak. The protocol addresses the reasons previous attempts fell short. No data are reported.

Keywords: sleep bruxism; dental implants; electromyography; polysomnography; implant stability; early loading; masticatory muscle activity; occlusal force

1. Introduction

Few beliefs in implant dentistry are held as firmly on as little direct evidence as the belief that bruxism endangers implants. A review two decades ago observed that bruxism is generally considered a contraindication for implants and that the evidence for this is usually based on clinical experience only [1]. Since then, observational studies have accumulated. A meta-analysis reported a risk ratio of 2.93 (95% CI 1.48–5.81) for implant failure in bruxers [2]; another, a pooled odds ratio of 4.72 at the prosthesis level [3]; a recent one, an odds ratio of 2.19 (95% CI 1.34–3.58) for implants in probable bruxers [4]; and a further review found a correlation in 12 of 15 included studies [5]. A large single-center analysis reached a similar conclusion with multilevel survival modeling [6]. In an early study of immediate loading, implants in patients with a parafunctional habit were lost more often [7].

The weakness of this literature lies in the exposure. An international consensus grades bruxism as possible when based on self-report, probable when supported by clinical inspection, and definite only when confirmed instrumentally, and it describes bruxism as a behavior on a continuum that should be assessed as such [8, 9]. The systematic review that first applied this lens to implants found 21 papers, noted the low specificity of the diagnostic approaches used, and concluded that evidence for bruxism as a cause of biological complications was lacking, with some suggestion of a role in mechanical complications [10]. The most recent meta-analysis could analyze only probable bruxism [4]. Self-report and tooth wear are poor proxies for current sleep-time muscle activity, and the reviews are in effect measuring something else: perhaps a trait, perhaps awake clenching, perhaps the clinician’s impression formed after a complication had already occurred.

Attempts to do better have been few. Polysomnography was used to confirm sleep bruxism in a retrospective series of implant patients [11]. A prospective cohort designed to relate electromyographically assessed sleep bruxism to implant complications was pre-registered and published as a protocol [12]; the follow-up report described insufficient participant recruitment and failed recordings and presented lessons learned [13]. A registry search found no registered study combining dental implants, sleep bruxism, and electromyography, and one registered evaluation of a portable recorder [14].

Two further gaps lie beneath the measurement problem. The first is timing. Complications studied to date are mostly late failures and mechanical events. The period when an implant is most vulnerable to load is the first weeks, when stability depends on a remodeling interface and tolerance of micromotion is limited [15]. Whether sleep-time loading during that window affects healing is unknown. The second is structure. Sleep bruxism does not load an implant evenly through the night. It occurs as episodes of rhythmic masticatory muscle activity associated with micro-arousals, often in clusters [16, 17], with large variation from night to night [18, 19]. Bone biology indicates that the temporal pattern of loading, including clustering and rest, influences the response of bone independently of magnitude [20, 21], and the one experiment on repeated daily loading sessions at a healing implant found more sessions to be worse [22]. A count of bruxism episodes may therefore be a less relevant exposure than their distribution, duration, and intensity.

This protocol describes a study that measures the exposure properly, at the time it is most likely to matter, with enough temporal resolution to ask whether pattern carries information, and with a design feature, a stratum of unloaded implants, that tests whether any association is mechanical.

2. Background and Current Scientific Evidence

Bruxism and implant outcomes

The meta-analytic estimates cited above are consistent in direction and heterogeneous in size. Their limitations are shared: retrospective designs; bruxism recorded from charts; no distinction between sleep and awake bruxism; unblinded outcome assessment; and failure defined variously. Narrative and systematic reviews of occlusal overload reach cautious conclusions and describe a possible synergy between mechanical overload and inflammation [23, 24]. A prosthodontic overview of bruxism definitions stresses that the construct has changed and that older studies cannot be read as if they measured what is now meant [25].

Instrumental assessment of sleep bruxism

Polysomnography with audio-video recording is the reference standard. Research diagnostic criteria based on the frequency of episodes and bursts were validated in a controlled study of 18 bruxers and 18 asymptomatic subjects [26]. Standard outcome variables are the number of episodes per hour of sleep, bursts per hour, and the bruxism time index [19]. Activity varies between nights within individuals, which affects both diagnosis and the evaluation of treatment [18, 19, 27].

Polysomnography is costly and unsuited to repeated nights at home. Portable devices have been compared with it. A device combining masseter electromyography with heart rate showed high correlation (r = 0.95) and agreement with polysomnography for episode counts [28]; another ambulatory system showed a non-significant correlation of 0.49 [29]. A systematic review judged the evidence on portable devices too scarce to support any as a stand-alone diagnostic method for research, with a possible exception [30], and a scoping review called for standardized reporting of recording and analysis procedures [31]. Multidimensional assessment frameworks are under development [32], and sensing and classification methods continue to advance [33].

From muscle activity to force on the implant

Electromyography measures muscle activation. The mechanical exposure of an implant is force, which depends on activation, jaw position, and the distribution of tooth contacts. Forces during sleep have been measured directly in a few studies. With force transducers in occlusal appliances worn for three nights, nocturnal bite forces during bruxism events were recorded in ten subjects and compared with daytime maximum voluntary force [34]. A piezoelectric intra-splint force detector identified sleep bruxism episodes with a median sensitivity of 0.861 and positive predictive value of 0.585 against electromyography, and the duration of detected force events correlated with that of electromyographic episodes (rho = 0.658) [35]. Deformation of occlusal appliances has been related to masseter activity [36].

Loads on implants in function have been measured with strain-gauged abutments and telemetry since the 1980s [37–39], and a review of three-dimensional in vivo load measurement concluded that such measurements are precise, that data are limited, and that simpler devices are needed [40]. None of these studies recorded implant loads during sleep in relation to healing.

Temporal organization of sleep bruxism

Rhythmic masticatory muscle activity follows a physiological sequence: cortical activation and a rise in heart rate precede jaw-muscle activity by seconds [16]. Episodes occur in relation to sleep micro-arousals and tend to cluster, with groups of episodes separated by less than 100 seconds [17]. The nightly exposure is therefore a series of bursts of loading, with long quiet intervals, whose number and intensity vary from night to night. This structure differs from daytime function, in which chewing occupies defined periods at a characteristic pace.

Why temporal pattern could matter for a healing implant

In intact bone, the osteogenic response to load saturates within a small number of cycles and is restored by rest [20, 21]. At a healing implant, tissue adjacent to the surface is immature and susceptible to damage from repeated strain, and increasing the number of daily loading sessions reduced bone-to-implant contact in a rat model [22]. If each cluster of bruxism episodes acts as an additional loading session delivered to tissue that has not recovered from the last, the number of clusters per night and the load delivered in each could matter more than the total episode count. This reasoning is a hypothesis drawn from animal data in different loading conditions. It motivates the choice of exposure metrics and is not presumed to be correct.

Measuring early healing

Resonance frequency analysis yields the implant stability quotient (ISQ), which typically falls in the first weeks after placement and then rises as bone forms [41]. The rise is the feature expected to be sensitive to adverse loading. ISQ can be measured repeatedly on implants with accessible abutment connections, including those carrying screw-retained provisional crowns that can be removed at visits.

Summary

An association between clinically judged bruxism and implant failure is established at the level of observational meta-analysis. Its interpretation is limited by exposure misclassification. Instruments for multi-night ambulatory assessment exist with variable validity. The temporal structure of sleep bruxism is well described. No study has related instrumentally measured sleep bruxism during healing to early implant outcomes.

3. Research Gap

The specific deficiencies are: no instrumental, multi-night measurement of sleep bruxism in an implant cohort that reached completion; no study focused on the healing period; no analysis of the temporal features of nocturnal activity in relation to implant outcomes; no estimate of the load that reaches the implant, as opposed to muscle activity in general; and no design element that distinguishes a mechanical effect from confounding by patient characteristics associated with bruxism.

The previous attempt at an instrumental cohort was undone by recruitment and recording failure [13]. A new protocol has to be built around feasibility: a short, well-defined follow-up; an outcome that every participant contributes; recording equipment and procedures piloted for home use; and a recording schedule tolerant of failed nights.

4. Research Objective and Central Hypothesis

The primary objective is to estimate the association between instrumentally measured sleep-time masticatory muscle activity during the first 12 weeks after implant placement and the gain in implant stability over that period, in implants loaded during healing.

The central hypothesis is that, in loaded implants, a higher nightly count of high-amplitude, long-duration masseter episodes is associated with a smaller gain in ISQ from week 2 to week 12, after adjustment for covariates; that the association is absent in unloaded implants; and that self-reported bruxism status is not associated with stability gain once instrumental measures are in the model.

Secondary hypotheses: (a) a force-weighted nightly load estimate that incorporates the implant’s share of occlusal contact is more strongly associated with the outcome than the episode index; (b) for a given nightly load, greater clustering of episodes is associated with a smaller stability gain; (c) instrumentally measured activity is associated with mechanical complications of the provisional restoration; (d) agreement between self-report and instrumental classification is poor.

The central hypothesis is refuted if no association is found in loaded implants with a confidence interval excluding the minimum effect of interest, or if the association is equally present in unloaded implants, which would indicate confounding.

5. Scientific and Theoretical Framework

Exposure chain

The path from sleep bruxism to the bone–implant interface has four links, each a source of attenuation or misclassification when ignored (Figure 1). Central motor events generate jaw-closing muscle activity. Muscle activity produces bite force in proportion to activation, modified by jaw position. Bite force is distributed over the occlusal contacts, and the implant restoration receives a share that depends on its contacts relative to those of the remaining dentition. That share produces interfacial micromotion in inverse proportion to current interface stiffness. Self-report samples the first link indirectly and unreliably. Electromyography measures the second. The study adds measurement or estimation of the third, and uses ISQ as an indicator of the fourth.

Exposure metrics

From each valid night of recording, the following are derived.

Conventional indices. Episodes per hour of sleep, bursts per hour, and bruxism time index, by published criteria [19, 26].

Intensity-resolved counts. The number of episodes whose peak amplitude exceeds a fraction of the individual’s maximum voluntary contraction amplitude and whose duration exceeds a set time. The primary exposure is the nightly count of episodes above 20% of maximum voluntary contraction lasting at least 2 seconds, averaged over valid nights; the thresholds are prespecified and varied in sensitivity analyses.

Nightly load estimate. For episode e with rectified, smoothed amplitude A_e(t) expressed as a fraction of maximum voluntary contraction and duration d_e,

L_(night)=s∑_e^​ ∫_0^d_e (c A_e(t))^m dt  (1)

where c is the individual’s calibration factor from electromyographic amplitude to bite force (N per unit normalized amplitude), s is the fraction of total occlusal force borne by the implant restoration, and m is an exponent that weights higher forces more heavily. With m=1, L_(night) is the force–time integral on the implant. Higher exponents correspond to damage-type weighting. The exponent is not known; m=1 is primary and m=2 and 3 are examined.

Temporal structure. The number of clusters per night, with a cluster defined as episodes separated by less than 100 seconds [17]; the mean number of episodes per cluster; the distribution of quiet intervals between clusters; and the proportion of the nightly load delivered in the largest cluster.

The unloaded stratum as a test of mechanism

Bruxism is associated with characteristics that could affect healing independently of load, including sleep disturbance, stress, smoking, and medication use. If these explain an association between bruxism and poorer healing, the association should appear whether or not the implant is loaded. If the association is mechanical, it should be confined to implants that receive occlusal force. The interaction between nocturnal activity and loading status is therefore the most informative single estimate in the study.

6. Methodology

Design and setting

Prospective cohort in specialist clinics, with 12 weeks of intensive follow-up and a 12-month visit, reported to STROBE [42]. A validation substudy compares the ambulatory recorder with polysomnography and is reported to STARD [43]. The protocol is registered before enrollment.

Participants and strata

Inclusion. Adults receiving one or two implants in healed posterior sites with opposing natural teeth or fixed restorations; adequate bone for standard-diameter implants without simultaneous augmentation beyond minor contouring; insertion torque and primary stability meeting the center’s criteria for the assigned protocol.

Strata. Stratum L (loaded): implants restored with a screw-retained provisional crown in light centric occlusion within two weeks of placement, under the center’s early-loading protocol. Stratum U (unloaded): implants healing with a healing abutment out of occlusion until week 12. Assignment follows clinical indication and patient preference and is not randomized; baseline characteristics are compared and adjusted for, and the strata are used to test interaction, not to compare healing between them.

Exclusion. Complete dentures opposing the site; removable appliance worn at night that the participant will not discontinue during recording blocks (participants prescribed a protective splint are enrolled in a separate descriptive stratum, since the splint alters the exposure); diagnosed sleep apnea under treatment with an oral appliance; medications with major effects on sleep motor activity, recorded and stratified if stable; pacemaker or condition interfering with the recorder.

Participants are recruited without regard to bruxism history, so that the cohort spans the continuum of activity. Recruitment materials do not mention bruxism as a selection criterion.

Instrumental assessment

Ambulatory recording. A portable recorder acquiring bilateral or unilateral masseter electromyography and heart rate, of a type compared against polysomnography [28], used at home for five consecutive nights in each of three blocks: block 1 in weeks 1–2, block 2 in weeks 5–6, block 3 in weeks 10–11. A night is valid if recording time and signal quality meet prespecified criteria. A block is valid with at least three valid nights. Participants are trained in electrode placement with a template, and the first night of the study is preceded by a supervised practice night that is not analyzed.

Calibration at each block. Maximum voluntary clench amplitude, for normalization, and graded clenches at 10%, 25%, 50%, and 75% of maximum on a bite-force transducer placed at the implant site region, to estimate the individual’s amplitude-to-force factor c. Normalization is repeated at each block because electrode placement varies.

Polysomnographic validation substudy. Thirty participants spanning the range of ambulatory episode index undergo one night of laboratory polysomnography with audio-video while wearing the ambulatory recorder. Agreement on episode index is assessed by Bland–Altman analysis and intraclass correlation [44, 45], and classification against research criteria [26] by sensitivity and specificity. Episode-level agreement on timing and duration is reported, since the temporal metrics depend on it.

Occlusal share. At each block, a digital occlusal analysis system records the relative force distribution in maximum intercuspation and in guided excursions; the proportion on the implant restoration is s in equation (1). The validity and reliability of such systems for relative force are limited and have been evaluated under laboratory conditions [46]; s is treated as an approximate modifier, and analyses are run with and without it. For stratum U, s is set to zero by design and verified by the absence of contact.

Self-report and clinical assessment. A standardized questionnaire and clinical examination for signs of bruxism, yielding the possible and probable grades [9], recorded before any instrumental data are available to the examiner. Awake bruxism is assessed by a one-week ecological momentary assessment in block 1.

Instrumented provisional (feasibility substudy). In a small subset of stratum L, a thin piezoelectric force sensor is embedded in the provisional crown or in a custom overlay, drawing on intra-splint detector designs [35], to record contact events on the implant directly during sleep. This substudy assesses feasibility and the agreement between directly sensed implant loading and the estimate from equation (1). It does not contribute to the primary analysis.

Outcomes

Primary. Gain in ISQ at the index implant from week 2 to week 12. Week 2 is used as the reference because it lies near the expected nadir and follows provisionalization. ISQ is measured at placement and at weeks 2, 4, 8, and 12, in two directions in duplicate, by an examiner blinded to all bruxism data; in stratum L the provisional crown is removed and replaced at each measurement with a controlled torque.

Secondary. ISQ trajectory modeled over all time points; marginal bone level change from provisionalization to 12 months on standardized radiographs read blind; early failure; mechanical complications of the provisional (screw loosening, fracture, decementation); patient-reported discomfort.

Covariates

Age, sex, smoking, diabetes, periodontal history, site and jaw, bone quality, implant dimensions, insertion torque, ISQ at placement, opposing dentition, number of occluding units, sleep quality by a validated questionnaire, caffeine and alcohol intake, and relevant medications.

Sample size

For the primary association in stratum L, treated as a correlation between the averaged primary exposure and ISQ gain, detecting a correlation of 0.25 with 80% power at two-sided α of 0.05 requires

n=((z_(1−α/2)+z_(1−β))/(1/2ln(1+r)/(1−r)))^2+3≈123  (2)

participants. The value r=0.25 is the minimum association judged worth detecting and is not an estimate from data. Because the exposure is measured with error, the true correlation corresponding to an observed 0.25 is larger (Section 7.1). Stratum U is planned at half that size, which gives limited power for the interaction; the interaction estimate is reported with its confidence interval and interpreted accordingly. Allowing 20% for invalid recordings and dropout, 150 participants are to be enrolled in stratum L and 75 in stratum U.

Statistical analysis

Primary. Linear regression of ISQ gain on the primary exposure in stratum L with adjustment for ISQ at week 2, covariates, and center. The interaction model pools both strata and includes exposure, stratum, and their product.

Comparison of exposure definitions. Models with self-report grade alone, conventional episode index, intensity-resolved count, and nightly load estimate are compared by explained variance and information criteria. The hypothesis is that explained variance rises along this sequence.

Temporal structure. Clustering metrics are added to a model containing nightly load to test whether pattern carries information beyond dose.

Time-varying analysis. A mixed model relates block-specific exposure to the change in ISQ over the following interval, exploiting the three blocks.

Misclassification. Agreement between self-report, clinical grade, and instrumental classification by kappa and by the distribution of instrumental indices within each grade.

Missing data. Participants with fewer than two valid blocks are excluded from the primary analysis and described. Multiple imputation is used for covariates [47].

Feasibility safeguards

Given the fate of the earlier instrumental cohort [13], the protocol includes a run-in phase of 20 participants to measure the proportion of valid nights and blocks, with prespecified criteria for proceeding (at least 80% of participants with two or more valid blocks). Devices are exchanged at visits already scheduled for ISQ measurement, adding no visits. Recording blocks of five nights tolerate two failed nights. Technical support by telephone is available during blocks, and data are downloaded and quality-checked at each visit so that a failed block can be repeated the following week.

Bias

Examiners of the outcome are blinded to exposure. Participants do not see their recordings during the study, to avoid behavior change. Recruitment is not based on bruxism status. Stratum assignment by indication is addressed by adjustment and by restricting inference from the strata to the interaction. Night-to-night variability is addressed by multi-night averaging and by the reliability analysis.

Ethics

Institutional review board approval and written consent. Participants receive standard implant care. If instrumental data reveal activity at a level the investigators judge clinically concerning, or if a provisional restoration shows mechanical damage, the treating clinician is informed and may prescribe a protective appliance; the participant then moves to the descriptive stratum from that date.

7. Analytical Development

Number of nights and regression dilution

Let the single-night reliability of an exposure metric, the intraclass correlation between nights within a person, be ρ_1. The reliability of the mean of k nights is

ρ_k=(k ρ_1)/(1+(k−1) ρ_1)  (3)

and an observed correlation with the outcome is attenuated by √(ρ_k) relative to the true correlation. If ρ_1 were 0.5, a value used only for illustration, one night would give reliability 0.5 and attenuate a true correlation of 0.35 to 0.25, while five nights would give 0.83 and fifteen nights 0.94. A single-night study would need roughly twice the sample to detect the same true association, and a null result from it would be nearly uninformative. The study estimates ρ_1 for each metric from its own data and reports dilution-corrected associations. The same calculation shows why temporal metrics, which are likely to be less stable from night to night than episode counts, need more nights. If their reliability over fifteen nights proves low, hypothesis (b) cannot be tested with this design, and that will be stated.

What episode counts miss

Two nights with the same episode index can differ greatly in mechanical exposure. Write the nightly load with m=1 as L=s c N A d, with N episodes of mean normalized amplitude A and mean duration d. The episode index captures only N. If amplitude and duration vary between people as much as frequency does, the index explains at most a third of the variance in log load when the three are independent, since logL is then the sum of three terms of equal variance. The implant-share term s adds a fourth, and it is zero for an implant out of occlusion. A patient with frequent, weak, brief episodes and an implant in infraocclusion, and another with rare, forceful, sustained clenching on an implant bearing the first contact, are misordered by the episode index. This is the quantitative argument for hypothesis (a).

Clustering and recovery

Suppose the tissue response to a loading bout depends on the state left by the previous bout, recovering with a time constant τ. For bouts separated by interval T, the fraction of recovery achieved is 1−e^(−T/τ). Episodes within a cluster, separated by under 100 seconds, arrive with almost no recovery if τ is of the order of minutes or longer, and so act as one prolonged bout; clusters separated by an hour arrive after substantial recovery if τ is under an hour. The effective number of independent loading bouts per night is then closer to the number of clusters than to the number of episodes, and the load per bout is the cluster load. Whether more, smaller bouts or fewer, larger ones are worse for a healing interface depends on whether damage rises faster than linearly with bout load, which is the role of the exponent m. With m>1, concentration of load into few clusters is worse at equal total. The analysis of the proportion of nightly load in the largest cluster addresses this directly. The time constant and exponent are unknown for human peri-implant tissue, and the argument indicates what to look for without predicting the outcome.

Expected pattern of results under competing explanations

If the conventional view is correct and bruxism mechanically impairs healing, the association appears in stratum L, strengthens from self-report to load estimate, and is absent in stratum U. If bruxism is a marker for patient factors, the association appears in both strata and is not strengthened by force weighting or occlusal share. If early-loaded implants with adequate primary stability are robust to the nocturnal loads actually experienced, no association appears, the confidence interval bounds the effect, and the conventional contraindication is not supported for this clinical scenario. Each pattern is distinguishable.

8. Discussion

The contribution intended here is evidentiary. The hypothesis that bruxism harms implants is old, and the meta-analyses appear to support it. What they support is an association between a clinician’s or patient’s label and implant loss, in studies where the label may have been applied after the loss. The protocol replaces the label with a measurement and places it at the time when a mechanical effect is most plausible.

There are reasons to think the result could go either way. On one side, the forces generated during sleep bruxism can be large and sustained, the healing interface tolerates limited micromotion, and immediate-loading studies reported more failures in bruxers [7]. On the other, implants selected for early loading have high primary stability, provisional crowns are kept in light occlusion, the natural dentition bears most of the load, and experimental overload of integrated implants without inflammation has not consistently caused bone loss [48]. An honest prior is that the average effect in a carefully selected early-loading population is small, and that harm, if any, is concentrated in a minority with intense activity and unfavorable occlusal share. The intensity-resolved and share-weighted metrics are designed to find that minority.

The principal threat to validity is measurement of the exposure. Ambulatory electromyography without audio-video overestimates bruxism by counting other orofacial activity; adding heart rate improves specificity [28], and the polysomnographic substudy quantifies residual error in this cohort. Normalization to maximum voluntary contraction is imperfect when electrodes are repositioned. The amplitude-to-force calibration is obtained awake, in a controlled clench, and may not hold for sleep activity at different jaw positions. The occlusal share is measured in voluntary closure, not during grinding. Each step adds noise, which biases toward the null. The instrumented provisional substudy offers a direct check on the composite estimate in a few participants.

The outcome is a surrogate. A smaller ISQ gain at 12 weeks is not implant failure, and an implant that stabilizes more slowly may do perfectly well. The justification is that failure is too rare to study in a cohort of this size, that ISQ trajectory is the most sensitive available indicator of early interface maturation, and that the 12-month marginal bone and complication data provide context.

Non-random assignment to loading strata limits the interaction test. Clinicians may avoid early loading in patients they believe to be bruxers, which would reduce the range of exposure in stratum L. Recruiting without reference to bruxism and recording the clinician’s reasons for protocol choice mitigate this. A design that randomized loading protocol would be cleaner and would raise ethical and practical objections that an observational first study avoids.

Awake bruxism may matter as much as sleep bruxism, since sustained low-level clenching can deliver large force–time integrals. The study measures it by self-report sampling only, which is a limitation acknowledged in the title’s focus on sleep.

9. Clinical Significance

A clear positive result, confined to loaded implants and scaling with estimated load, would justify instrumental screening before early or immediate loading in place of history-taking, would identify the features of nocturnal activity that carry risk, and would support trials of protective measures during healing. It would also give occlusal design of provisional restorations a quantitative target, since the implant’s share of force is the factor most readily modified.

A clear null result within a well-measured range would be equally consequential. It would indicate that, for implants with good primary stability provisionalized in light occlusion, sleep bruxism as it occurs in an unselected population does not measurably impair early healing, and that the routine exclusion of patients labeled as bruxers from early-loading protocols lacks support. The result would not extend to full-arch immediate loading or to late mechanical complications, which require their own studies.

Until then, current clinical caution remains reasonable, and its evidence base should be described accurately as an association with a clinical label.

10. Limitations

The study is observational, and loading stratum is assigned by indication. Exposure measurement involves several steps of calibration and estimation, each with error. The ambulatory recorder’s validity is established for episode counts and less so for amplitude, duration, and timing. The polysomnographic substudy is a single laboratory night and subject to first-night effects. Fifteen nights may be insufficient for stable estimates of temporal metrics. ISQ is a surrogate, and removing provisional crowns to measure it is itself a small perturbation, applied equally across exposure levels. The cohort is restricted to posterior single or two-unit sites and to patients suitable for the stated protocols. The sample size rests on an assumed minimum correlation. Awake bruxism is assessed only by self-report. Thresholds in the primary exposure are prespecified without empirical precedent. The literature was assessed from abstracts and index records, including the report of the earlier cohort.

11. Future Validation

If an association is found, replication in an independent cohort with the same exposure definitions is required. A randomized trial of a protective intervention during healing in patients above an instrumental threshold would test causality. Extension to immediately loaded full-arch rehabilitation, where forces on implants are higher and the clinical stakes greater, should use instrumented provisional prostheses if the feasibility substudy succeeds. Development of a validated sensor that records load on the implant restoration directly during sleep would remove most of the estimation steps, and the review of in vivo load measurement identifies that as an unmet need [40].

12. Conclusion

The association between bruxism and implant failure rests on clinical labels, and the one prospective study designed to measure sleep bruxism instrumentally in implant patients could not be completed as planned. This protocol specifies a cohort that measures sleep-time masticatory muscle activity over multiple nights during healing, estimates the load reaching the implant, examines the temporal organization of that load, and uses unloaded implants to test whether any association is mechanical. Simple reliability and variance arguments show why single-night recordings and episode counts are inadequate for the purpose. The study would provide the first direct evidence on whether sleep bruxism affects early implant healing. It has not been performed.

Cite this paper

Jain S, Gupta A. Sleep-Related Mechanical Loading and Early Implant Healing: A Prospective, Time-Resolved, Instrumentally Assessed Cohort Protocol for Nocturnal Bruxism. Working paper. Center for Implant Dentistry; 2026. Available from: https://bayareaimplantdentistry.com/clinician-research-and-publications/sleep-loading-early-implant-healing

References

  1. Lobbezoo F, Brouwers JE, Cune MS, Naeije M. Dental implants in patients with bruxing habits. J Oral Rehabil. 2006;33(2):152-9. doi:10.1111/j.1365-2842.2006.01542.x (opens in a new tab). PMID: 16457676 (opens in a new tab).
  2. Chrcanovic BR, Albrektsson T, Wennerberg A. Bruxism and Dental Implants: A Meta-Analysis. Implant Dent. 2015;24(5):505-16. doi:10.1097/ID.0000000000000298 (opens in a new tab). PMID: 26218253 (opens in a new tab).
  3. Zhou Y, Gao J, Luo L, Wang Y. Does Bruxism Contribute to Dental Implant Failure? A Systematic Review and Meta-Analysis. Clin Implant Dent Relat Res. 2016;18(2):410-20. doi:10.1111/cid.12300 (opens in a new tab). PMID: 25726844 (opens in a new tab).
  4. Häggman-Henrikson B, Ali D, Aljamal M, Chrcanovic BR. Bruxism and dental implants: A systematic review and meta-analysis. J Oral Rehabil. 2024;51(1):202-217. doi:10.1111/joor.13567 (opens in a new tab). PMID: 37589382 (opens in a new tab).
  5. Ionfrida JA, Stiller HL, Kämmerer PW, Walter C. Dental Implant Failure Risk in Patients with Bruxism-A Systematic Review and Meta-Analysis of the Literature. Dent J (Basel). 2024;13(1). doi:10.3390/dj13010011 (opens in a new tab). PMID: 39851587 (opens in a new tab).
  6. Chrcanovic BR, Kisch J, Albrektsson T, Wennerberg A. Bruxism and dental implant failures: a multilevel mixed effects parametric survival analysis approach. J Oral Rehabil. 2016;43(11):813-823. doi:10.1111/joor.12431 (opens in a new tab). PMID: 27611304 (opens in a new tab).
  7. Glauser R, Rée A, Lundgren A, Gottlow J, Hämmerle CH, Schärer P. Immediate occlusal loading of Brånemark implants applied in various jawbone regions: a prospective, 1-year clinical study. Clin Implant Dent Relat Res. 2001;3(4):204-13. doi:10.1111/j.1708-8208.2001.tb00142.x (opens in a new tab). PMID: 11887657 (opens in a new tab).
  8. Lobbezoo F, Ahlberg J, Glaros AG, Kato T, Koyano K, Lavigne GJ, et al. Bruxism defined and graded: an international consensus. J Oral Rehabil. 2013;40(1):2-4. doi:10.1111/joor.12011 (opens in a new tab). PMID: 23121262 (opens in a new tab).
  9. Lobbezoo F, Ahlberg J, Raphael KG, Wetselaar P, Glaros AG, Kato T, et al. International consensus on the assessment of bruxism: Report of a work in progress. J Oral Rehabil. 2018;45(11):837-844. doi:10.1111/joor.12663 (opens in a new tab). PMID: 29926505 (opens in a new tab).
  10. Manfredini D, Poggio CE, Lobbezoo F. Is bruxism a risk factor for dental implants? A systematic review of the literature. Clin Implant Dent Relat Res. 2014;16(3):460-9. doi:10.1111/cid.12015 (opens in a new tab). PMID: 23151302 (opens in a new tab).
  11. Tosun T, Karabuda C, Cuhadaroglu C. Evaluation of sleep bruxism by polysomnographic analysis in patients with dental implants. Int J Oral Maxillofac Implants. 2003;18(2):286-92. PMID: 12705309 (opens in a new tab).
  12. Thymi M, Visscher CM, Yoshida-Kohno E, Crielaard W, Wismeijer D, Lobbezoo F. Associations between sleep bruxism and (peri-) implant complications: a prospective cohort study. BDJ Open. 2017;3:17003. doi:10.1038/bdjopen.2017.3 (opens in a new tab). PMID: 29607076 (opens in a new tab).
  13. Thymi M, Visscher CM, Wismeijer D, Lobbezoo F. Associations between sleep bruxism and (peri-)implant complications: lessons learned from a clinical study. BDJ Open. 2020;6:2. doi:10.1038/s41405-020-0028-6 (opens in a new tab). PMID: 32577305 (opens in a new tab).
  14. ClinicalTrials.gov. Identifier NCT06096753 (University of Turin; evaluation of a portable EMG/ECG bruxism recorder). Bethesda (MD): National Library of Medicine (US).
  15. Szmukler-Moncler S, Salama H, Reingewirtz Y, Dubruille JH. Timing of loading and effect of micromotion on bone-dental implant interface: review of experimental literature. J Biomed Mater Res. 1998;43(2):192-203. doi:10.1002/(sici)1097-4636(199822)43:2<192::aid-jbm14>3.0.co;2-k (opens in a new tab). PMID: 9619438 (opens in a new tab).
  16. Kato T, Rompré P, Montplaisir JY, Sessle BJ, Lavigne GJ. Sleep bruxism: an oromotor activity secondary to micro-arousal. J Dent Res. 2001;80(10):1940-4. doi:10.1177/00220345010800101501 (opens in a new tab). PMID: 11706956 (opens in a new tab).
  17. Huynh N, Kato T, Rompré PH, Okura K, Saber M, Lanfranchi PA, et al. Sleep bruxism is associated to micro-arousals and an increase in cardiac sympathetic activity. J Sleep Res. 2006;15(3):339-46. doi:10.1111/j.1365-2869.2006.00536.x (opens in a new tab). PMID: 16911037 (opens in a new tab).
  18. Lavigne GJ, Guitard F, Rompré PH, Montplaisir JY. Variability in sleep bruxism activity over time. J Sleep Res. 2001;10(3):237-44. doi:10.1046/j.1365-2869.2001.00261.x (opens in a new tab). PMID: 11696077 (opens in a new tab).
  19. Van Der Zaag J, Lobbezoo F, Visscher CM, Hamburger HL, Naeije M. Time-variant nature of sleep bruxism outcome variables using ambulatory polysomnography: implications for recognition and therapy evaluation. J Oral Rehabil. 2008;35(8):577-84. doi:10.1111/j.1365-2842.2008.01893.x (opens in a new tab). PMID: 18699969 (opens in a new tab).
  20. Robling AG, Burr DB, Turner CH. Recovery periods restore mechanosensitivity to dynamically loaded bone. J Exp Biol. 2001;204(Pt 19):3389-99. doi:10.1242/jeb.204.19.3389 (opens in a new tab). PMID: 11606612 (opens in a new tab).
  21. Srinivasan S, Weimer DA, Agans SC, Bain SD, Gross TS. Low-magnitude mechanical loading becomes osteogenic when rest is inserted between each load cycle. J Bone Miner Res. 2002;17(9):1613-20. doi:10.1359/jbmr.2002.17.9.1613 (opens in a new tab). PMID: 12211431 (opens in a new tab).
  22. de Barros E Lima Bueno R, Dias AP, Ponce KJ, Wazen R, Brunski JB, Nanci A. Bone healing response in cyclically loaded implants: Comparing zero, one, and two loading sessions per day. J Mech Behav Biomed Mater. 2018;85:152-161. doi:10.1016/j.jmbbm.2018.05.044 (opens in a new tab). PMID: 29894930 (opens in a new tab).
  23. Mojaver S, Patel N, Sarmiento H, Fiorellini JP. Under pressure: Unraveling the impact of occlusal overload on peri-implant health-A systematic review. J Prosthodont. 2025;34(8):784-795. doi:10.1111/jopr.14088 (opens in a new tab). PMID: 40571905 (opens in a new tab).
  24. Shafiee E, Nourizadeh A. Bruxism in implant-supported rehabilitations: a narrative review of clinical complications and management strategies. BMC Oral Health. 2025;25(1):1586. doi:10.1186/s12903-025-07005-y (opens in a new tab). PMID: 41068723 (opens in a new tab).
  25. Manfredini D, Ahlberg J, Lobbezoo F. Bruxism definition: Past, present, and future - What should a prosthodontist know?. J Prosthet Dent. 2022;128(5):905-912. doi:10.1016/j.prosdent.2021.01.026 (opens in a new tab). PMID: 33678438 (opens in a new tab).
  26. Lavigne GJ, Rompré PH, Montplaisir JY. Sleep bruxism: validity of clinical research diagnostic criteria in a controlled polysomnographic study. J Dent Res. 1996;75(1):546-52. doi:10.1177/00220345960750010601 (opens in a new tab). PMID: 8655758 (opens in a new tab).
  27. Minakuchi H, Sakaguchi C, Hara ES, Maekawa K, Matsuka Y, Clark GT, et al. Multiple sleep bruxism data collected using a self-contained EMG detector/analyzer system in asymptomatic healthy subjects. Sleep Breath. 2012;16(4):1069-72. doi:10.1007/s11325-011-0602-1 (opens in a new tab). PMID: 22278147 (opens in a new tab).
  28. Castroflorio T, Deregibus A, Bargellini A, Debernardi C, Manfredini D. Detection of sleep bruxism: comparison between an electromyographic and electrocardiographic portable holter and polysomnography. J Oral Rehabil. 2014;41(3):163-9. doi:10.1111/joor.12131 (opens in a new tab). PMID: 24417585 (opens in a new tab).
  29. Yamaguchi T, Abe S, Rompré PH, Manzini C, Lavigne GJ. Comparison of ambulatory and polysomnographic recording of jaw muscle activity during sleep in normal subjects. J Oral Rehabil. 2012;39(1):2-10. doi:10.1111/j.1365-2842.2011.02232.x (opens in a new tab). PMID: 21707698 (opens in a new tab).
  30. Manfredini D, Ahlberg J, Castroflorio T, Poggio CE, Guarda-Nardini L, Lobbezoo F. Diagnostic accuracy of portable instrumental devices to measure sleep bruxism: a systematic literature review of polysomnographic studies. J Oral Rehabil. 2014;41(11):836-42. doi:10.1111/joor.12207 (opens in a new tab). PMID: 25040303 (opens in a new tab).
  31. Thymi M, Lobbezoo F, Aarab G, Ahlberg J, Baba K, Carra MC, et al. Signal acquisition and analysis of ambulatory electromyographic recordings for the assessment of sleep bruxism: A scoping review. J Oral Rehabil. 2021;48(7):846-871. doi:10.1111/joor.13170 (opens in a new tab). PMID: 33772835 (opens in a new tab).
  32. Manfredini D, Ahlberg J, Aarab G, Bracci A, Durham J, Ettlin D, et al. Towards a Standardized Tool for the Assessment of Bruxism (STAB)-Overview and general remarks of a multidimensional bruxism evaluation system. J Oral Rehabil. 2020;47(5):549-556. doi:10.1111/joor.12938 (opens in a new tab). PMID: 31999846 (opens in a new tab).
  33. Gul JZ, Fatima N, Mohy Ud Din Z, Khan M, Kim WY, Rehman MM. Advanced Sensing System for Sleep Bruxism across Multiple Postures via EMG and Machine Learning. Sensors (Basel). 2024;24(16). doi:10.3390/s24165426 (opens in a new tab). PMID: 39205120 (opens in a new tab).
  34. Nishigawa K, Bando E, Nakano M. Quantitative study of bite force during sleep associated bruxism. J Oral Rehabil. 2001;28(5):485-91. doi:10.1046/j.1365-2842.2001.00692.x (opens in a new tab). PMID: 11380790 (opens in a new tab).
  35. Aoki R, Takaba M, Abe Y, Nakazato Y, Ohara H, Maejima K, et al. A pilot study to test the validity of a piezoelectric intra-splint force detector for monitoring of sleep bruxism in comparison to portable polysomnography. J Oral Sci. 2022;64(1):63-68. doi:10.2334/josnusd.21-0421 (opens in a new tab). PMID: 34955491 (opens in a new tab).
  36. Ozawa A, Suzuki Y, Okura K, Tajima T, Taniwaki T, Shibagaki A, et al. Evaluation of sleep bruxism by three-dimensional analysis of the deformation of acrylic resin occlusal appliances. J Prosthodont Res. 2026;70(1):141-150. doi:10.2186/jpr.JPR_D_24_00315 (opens in a new tab). PMID: 40634083 (opens in a new tab).
  37. Brunski JB, Hipp JA. In vivo forces on dental implants: hard-wiring and telemetry methods. J Biomech. 1984;17(11):855-60. doi:10.1016/0021-9290(84)90144-1 (opens in a new tab). PMID: 6520134 (opens in a new tab).
  38. Morneburg TR, Pröschel PA. In vivo forces on implants influenced by occlusal scheme and food consistency. Int J Prosthodont. 2003;16(5):481-6. PMID: 14651231 (opens in a new tab).
  39. Duyck J, Van Oosterwyck H, Vander Sloten J, De Cooman M, Puers R, Naert I. Magnitude and distribution of occlusal forces on oral implants supporting fixed prostheses: an in vivo study. Clin Oral Implants Res. 2000;11(5):465-75. doi:10.1034/j.1600-0501.2000.011005465.x (opens in a new tab). PMID: 11168239 (opens in a new tab).
  40. Assoratgoon I, Yoda N, Iwamoto M, Sato T, Kawata T, Egusa H, et al. In vivo measurement of three-dimensional load exerted on dental implants: a literature review. Int J Implant Dent. 2022;8(1):52. doi:10.1186/s40729-022-00454-y (opens in a new tab). PMID: 36372828 (opens in a new tab).
  41. Sennerby L, Meredith N. Implant stability measurements using resonance frequency analysis: biological and biomechanical aspects and clinical implications. Periodontol 2000. 2008;47:51-66. doi:10.1111/j.1600-0757.2008.00267.x (opens in a new tab). PMID: 18412573 (opens in a new tab).
  42. von Elm E, Altman DG, Egger M, Pocock SJ, Gøtzsche PC, Vandenbroucke JP. The Strengthening the Reporting of Observational Studies in Epidemiology (STROBE) statement: guidelines for reporting observational studies. Lancet. 2007;370(9596):1453-7. doi:10.1016/S0140-6736(07)61602-X (opens in a new tab). PMID: 18064739 (opens in a new tab).
  43. Bossuyt PM, Reitsma JB, Bruns DE, Gatsonis CA, Glasziou PP, Irwig L, et al. STARD 2015: an updated list of essential items for reporting diagnostic accuracy studies. BMJ. 2015;351:h5527. doi:10.1136/bmj.h5527 (opens in a new tab). PMID: 26511519 (opens in a new tab).
  44. Bland JM, Altman DG. Statistical methods for assessing agreement between two methods of clinical measurement. Lancet. 1986;1(8476):307-10. PMID: 2868172 (opens in a new tab).
  45. Koo TK, Li MY. A Guideline of Selecting and Reporting Intraclass Correlation Coefficients for Reliability Research. J Chiropr Med. 2016;15(2):155-63. doi:10.1016/j.jcm.2016.02.012 (opens in a new tab). PMID: 27330520 (opens in a new tab).
  46. Cerna M, Ferreira R, Zaror C, Navarro P, Sandoval P. Validity and reliability of the T-Scan(®) III for measuring force under laboratory conditions. J Oral Rehabil. 2015;42(7):544-51. doi:10.1111/joor.12284 (opens in a new tab). PMID: 25727489 (opens in a new tab).
  47. Sterne JA, White IR, Carlin JB, Spratt M, Royston P, Kenward MG, et al. Multiple imputation for missing data in epidemiological and clinical research: potential and pitfalls. BMJ. 2009;338:b2393. doi:10.1136/bmj.b2393 (opens in a new tab). PMID: 19564179 (opens in a new tab).
  48. Heitz-Mayfield LJ, Schmid B, Weigel C, Gerber S, Bosshardt DD, Jönsson J, et al. Does excessive occlusal load affect osseointegration? An experimental study in the dog. Clin Oral Implants Res. 2004;15(3):259-68. doi:10.1111/j.1600-0501.2004.01019.x (opens in a new tab). PMID: 15142087 (opens in a new tab).