Skip to main content

Which Error Matters in Complete-Arch Digital Implant Records? A Pose-Based Metrology Framework for Intraoral Scanning and Photogrammetry and a Test of the Angular-Error Hypothesis of Prosthesis Misfit

Paper type
Technical methodology article with an embedded laboratory validation protocol and invention disclosure appendix
Status
Original Work · Working Paper
Keywords:
digital implant impression · intraoral scanner · photogrammetry · trueness and precision · passive fit · scan body · measurement uncertainty · complete-arch prosthesis
Contents
  1. 1Introduction and Clinical Significance
  2. 2Critical Review of the Established Literature
  3. 3Identification of the Specific Research Gap
  4. 4Scientific Objective and Hypothesis
  5. 5Theoretical Foundation
  6. 6Methodology
  7. 7Evidence Synthesis and Explicitly Labeled Theoretical Predictions
  8. 8Discussion: Mechanisms and Competing Explanations
  9. 9Implications for Implant Prosthodontics
  10. 10Technical and Clinical Limitations
  11. 11Proposed Experimental and Clinical Validation
  12. 12Future Research Directions
  13. 13Evidence-Calibrated Conclusion

Abstract

Background: Complete-arch implant prostheses require that the recorded positions and orientations of several implants agree with reality closely enough for a rigid framework to seat without harmful strain. Intraoral scanners accumulate error across the arch, and photogrammetric systems were introduced to avoid it. Accuracy studies report deviations in different and often incomparable ways, and no threshold of clinically acceptable misfit has been established.

Objective: To review how accuracy of complete-arch implant records is measured, to propose a measurement framework that isolates the error components relevant to framework fit, and to design experiments that test whether angular or linear error governs misfit strain.

Methods: Critical review of systematic reviews and laboratory studies, with attention to reference standards, alignment methods, and outcome definitions. A pose-based error model was formulated in which each implant is described by a position and an axis, and accuracy is expressed as errors in inter-implant distances and angles. Elementary beam theory was used to compare the bending moments produced by imposed linear and angular misfit. A laboratory protocol was specified in two parts: a repeatability and reproducibility study of capture methods against a coordinate measuring machine, and a factorial imposed-error study with strain-gauged frameworks.

Findings: Pooled laboratory evidence favors photogrammetry over intraoral scanning for trueness and precision of complete-arch records, with differences of tens of micrometers and substantial heterogeneity; clinical outcome evidence is absent. Best-fit superimposition, the commonest analysis, distributes cross-arch error and can understate it. The mechanical analysis predicts that an angular error of half a degree between implants 20 mm apart induces a bending moment equal to that of a vertical step of about 115 µm, and that the relative importance of angular error grows with span. We hypothesize that inter-implant angular error explains more of the variance in tightening strain than inter-implant distance error.

Conclusions: The useful question is not which device has the smallest average deviation but whether the pose errors that load a framework are controlled and reported. The hypothesis and equivalence relations given here are theoretical and require the bench validation described.

Keywords: digital implant impression; intraoral scanner; photogrammetry; trueness and precision; passive fit; scan body; measurement uncertainty; complete-arch prosthesis

1. Introduction and Clinical Significance

A fixed prosthesis that joins several implants is a statically indeterminate structure. Unlike teeth, osseointegrated implants have no ligament to accommodate small positional discrepancies, so any difference between the geometry of the framework and the geometry of the implants must be taken up by elastic deformation of the framework, the screws, the implants, and the bone when the screws are tightened. The idea that a framework should seat passively, without inducing strain, has been a tenet of implant prosthodontics since the first clinical protocols, and its literature has been reviewed repeatedly [1, 2]. The same reviews acknowledge that absolute passivity is unattainable, that there is no agreed method of measuring fit clinically [3], and that no threshold of acceptable misfit has been validated.

The clinical consequences of misfit are better documented for hardware than for bone. A classic study measured framework misfit by three-dimensional photogrammetry in edentulous patients and found no association between the degree of misfit and marginal bone loss over several years [4]; an experiment in primates with prostheses of deliberately different fit likewise found no difference in the bone response around unloaded implants [5]. A systematic review of misfit and clinical outcomes concluded that the evidence for biological harm is weak, while the association with technical complications such as screw loosening and fracture is biologically plausible and supported mainly by laboratory data [6]. Technical complications are, however, the dominant burden of complete-arch implant prostheses over time [7], which is reason enough to care about fit.

Digital workflows have changed how implant positions are recorded. Intraoral scanners capture scan bodies attached to the implants and assemble a surface from overlapping images; photogrammetric systems record coded targets with calibrated cameras and compute their positions directly. Both replace the splinted impression and the verification cast, and both are marketed with accuracy figures in micrometers. Clinicians must decide whether those figures mean that a milled framework will fit. This paper argues that, as usually reported, they do not answer that question, and it proposes measurements that would.

2. Critical Review of the Established Literature

Conventional records

Systematic review of implant impression accuracy found that for completely edentulous patients splinted techniques were more accurate than non-splinted techniques and open-tray more accurate than closed-tray in the majority of studies [8]. The splinted open-tray impression with a verification jig is the conventional comparator in most studies of digital methods, although it is itself a measurement with error and cannot serve as a reference standard.

Intraoral scanning

Intraoral scanners reconstruct a surface by registering successive small fields of view to one another [9]. Each registration carries a small error, and across a long path the errors accumulate. Studies of complete-arch scans of dentate models described increasing deviation with distance from the starting point and distortion at the distal ends of the arch [10], and in vivo precision of complete-arch scans was lower than that of conventional impressions in an early comparison [11]. An in vivo method based on reference geometry confirmed that scanner performance varied between devices and that cross-arch deviations were the largest [12], and a measuring gauge placed in the mouth showed accuracy worsening as the scanned span lengthened [13].

The edentulous arch with implants is the most difficult case, because the mucosa between scan bodies is smooth, mobile, and poor in features. Laboratory studies reported that deviations rose with the distance scanned and were affected by operator experience and implant angulation and depth [14], and that different scanners produced position errors of different size on the same multi-implant model [15]. A systematic review and meta-analysis of impression techniques for implant-supported prostheses concluded that the available data on digital and conventional implant impressions were of a low evidence level and lacked sufficient in vivo data to support clinical recommendations [16]; a meta-analysis restricted to digital versus conventional implant impressions found comparable three-dimensional accuracy, based mainly on in vitro studies [17]; and systematic reviews specific to complete-arch digital scans reported wide ranges of deviation and identified scanner, scan strategy, inter-implant distance, and scan-body design as sources of variation [18, 19]. A study that compared digital and conventional implant impressions for edentulous jaws found the three-dimensional deviations of digital casts to be within the range of conventional ones for the system tested [20].

Scan bodies introduce their own error. They differ in material, geometry, and how reproducibly they seat, and the alignment of a scanned scan-body surface to its library model is a best-fit operation whose angular uncertainty depends on the extent and quality of the captured surface [21]. Techniques intended to reduce stitching error by giving the scanner more features, such as auxiliary geometric devices that bridge the edentulous spans, improved accuracy in laboratory tests [22], and different scan-body designs and scanning techniques gave significantly different results on complete-arch models [23]. A calibrated protocol in which a reference of known geometry is used to correct the scan has been reported to approach the accuracy of the splinted conventional impression in vitro [24].

Photogrammetry

Photogrammetry was applied to implant prosthodontics three decades ago as a measuring tool, first to record implant positions and then to quantify the fit between frameworks and master casts [25, 26]. Its clinical use as an impression method came later, with extraoral stereo cameras that image coded flags screwed to the implants [27, 28]. Because every target is located by triangulation in the coordinate frame of a calibrated camera pair, error does not accumulate along the arch as it does with stitched surface scans. The method records implant positions only; soft tissue must be captured separately and merged.

Laboratory comparisons with a coordinate measuring machine as reference found that photogrammetry, intraoral scanning, and conventional impressions differed significantly, with the ranking depending on the specific devices and on whether linear or angular discrepancy was considered [29]. Other in vitro studies reported smaller deviations for stereophotogrammetry than for intraoral scanning on complete-arch models [30, 31]. A recent systematic review and meta-analysis concluded that photogrammetry showed better trueness and precision than intraoral scanning for complete-arch digital implant impressions, on the basis of predominantly in vitro studies with substantial heterogeneity [32], and two further syntheses comparing stereophotogrammetry with intraoral scanners reached compatible conclusions [33, 34]. None of the pooled studies used a clinical outcome.

Manufacturing

The record is only the first link. The designed framework must be manufactured, by milling or by additive methods, and each process has its own error [35]. Computer numeric controlled milling of titanium frameworks produced fit comparable to or better than casting in early comparisons [36], and a comparison of computer-aided fabrication of long- and short-span frameworks found all within clinically acceptable values, with the short-span frameworks statistically more precise [37]. A systematic review of screw-retained framework fit by fabrication method found computer-aided milling to be among the most accurate techniques while noting inconsistent measurement methods [38].

How accuracy is measured

The international standard on accuracy of measurement methods defines trueness as closeness of agreement between the mean of a large series of results and an accepted reference value, and precision as closeness of agreement among independent results under stipulated conditions, with repeatability and reproducibility as its two extremes [39]. A standard specific to digital impression devices describes test objects and procedures for assessing them [40]. Dental accuracy studies use these terms but often depart from the underlying requirements: the reference is frequently a desktop scanner whose own uncertainty is unstated; "precision" is computed from pairwise comparison of a handful of scans by one operator; and deviation is computed after best-fit superimposition of the entire test surface on the reference.

The superimposition step deserves particular attention. Best-fit alignment minimizes the sum of squared distances between surfaces, which spreads a systematic cross-arch error over the whole arch and reports a smaller figure than the discrepancy between the two ends. The choice of alignment method and reference area changes the result materially [41]. For an implant framework what matters is the relation of each implant to the others, and a metric that depends on an arbitrary alignment obscures it. One early study of intraoral scanning of multiple implants avoided the problem by reporting inter-implant distance and angulation errors and proposed tolerances for each derived from an assumed permissible implant displacement [42].

3. Identification of the Specific Research Gap

The following can be regarded as established. Splinted conventional impressions are accurate enough to have supported decades of complete-arch prosthodontics. Intraoral scans accumulate error with scan length, most severely in edentulous arches. Photogrammetry shows smaller position deviations than intraoral scanning in laboratory studies. Milled frameworks reproduce their design with a precision that is somewhat better for short than for long spans.

Three things are unknown. The first is which component of record error matters mechanically. A record can be wrong in the distances between implants, in the heights of their platforms, in the directions of their axes, or in rotation about those axes, and the framework responds differently to each. The second is how capture error combines with design and manufacturing error. The third is what magnitude of each error is tolerable.

The methods are inadequate in specific ways. Deviations after best-fit alignment are not frame-invariant and mix position and orientation. Angular error is reported in a minority of studies. Reference measurements often lack a stated uncertainty, so that differences of 10 or 20 µm between methods are compared against a reference that may be no better. Sample sizes of ten scans by one operator estimate repeatability, not reproducibility. And almost no study carries the record through to a manufactured framework and measures what the clinician cares about, which is the strain at tightening.

4. Scientific Objective and Hypothesis

The objectives are to define a set of error measures for complete-arch implant records that is independent of alignment and separates linear from angular components, and to determine experimentally which component governs the strain produced when a framework made from an erroneous record is tightened onto the true implant positions.

Hypothesis H16: across the range of errors produced by current capture methods, inter-implant angular error explains more of the variance in framework strain at screw tightening than inter-implant distance error.

The hypothesis is falsified if, in a factorial experiment in which linear and angular errors are imposed independently on machined frameworks and strain is measured with gauges, the proportion of variance in peak strain attributable to linear error exceeds that attributable to angular error, with a confidence interval for the difference that excludes zero. An interval that includes zero would leave the hypothesis unsupported. The comparison is meaningful only over ranges of linear and angular error that correspond to what devices actually produce, and those ranges are fixed in Part A of the protocol before Part B is run.

5. Theoretical Foundation

Pose and frame-invariant error

The position and orientation of implant i are described by the coordinates of a reference point on its platform, the vector pi, and a unit vector ui along its axis; for connections with an anti-rotation feature a third quantity, the rotation about the axis, completes the pose. A record of N implants is correct for prosthetic purposes if it reproduces the relations among the implants, whatever coordinate frame it is expressed in. Two families of quantities capture those relations without reference to any frame. The inter-implant distance error for the pair i, j is

Δd_(ij) = |p_i - p_j|_(test) - |p_i - p_j|_(ref) (1)

in micrometers, and the inter-implant angle error is

Δθ_(ij) = arccos(u_i · u_j)_(test) - arccos(u_i · u_j)_(ref) (2)

in degrees. With N implants there are N(N − 1)/2 pairs. Trueness is summarized by the mean signed error for each pair over repeated records, precision by the standard deviation, and both are reported as functions of the true inter-implant distance, so that accumulation along the arch is visible. Height discrepancies normal to the occlusal plane are contained in the set of distances but are more easily interpreted when the error vector for each pair is resolved along and across the mean implant axis; this decomposition requires only the two implants of the pair and not a global alignment.

Accumulation in stitched scans

If each registration between successive frames contributes an independent random error and a small systematic bias, the standard uncertainty of the distance between two points separated by a scan path of length s grows as

σ_d(s) = √(σ_1^2 s/l + (b s)^2) (3)

where σ1 is the random error per registration step, l the step length, and b a dimensionless drift coefficient. The first term grows with the square root of path length and the second linearly. The expression is a schematic of the behavior described in complete-arch studies [10, 14] and not a calibrated model of any device; its use is to make explicit that precision reported for a quadrant cannot be extrapolated to the arch and that systematic drift, which affects trueness, will dominate over long paths. Triangulated photogrammetry has no path-dependent term, and its uncertainty depends on camera geometry, target quality, and working distance.

From scan-body orientation to platform position

A scan body is registered by fitting its captured surface to a library shape. If the fitted axis is in error by a small angle δθ, in radians, about a point at height h above the implant platform, the inferred platform position is displaced laterally by approximately

e_p = h δθ (4)

With h of 8 mm, an orientation error of 0.5 degree (0.0087 rad) displaces the platform by about 70 µm. Angular error at capture is therefore converted into linear error at the platform in proportion to scan-body height, and tall scan bodies that are easier to scan are also longer levers. The two errors are correlated by construction, which must be taken into account when their effects are separated experimentally.

Misfit moments in a framework

Consider the segment of framework between two adjacent implants as a prismatic beam of length L, elastic modulus E, and second moment of area I, rigidly held at one implant. If the seat at the other implant is offset vertically by δ and tightening forces it into contact without rotation, the bending moment at each end is

M_δ = (6 E I δ)/(L^2) (5)

If the seat is correctly positioned but tilted by an angle φ and tightening forces it flat, the moment at that end is

M_φ = (4 E I φ)/L (6)

Equating the two gives the vertical offset that is mechanically equivalent to a given angular misfit:

δ_(eq) = 2/3 φ L (7)

For φ of 0.5 degree and L of 20 mm, δeq is about 116 µm; for L of 40 mm it is about 233 µm. The ratio of the moments for errors of given size, Mφ/Mδ = 2φL/(3δ), increases with span. The idealization ignores the compliance of screws, abutments, implants, and bone, the finite area and geometry of the seating surfaces, and the fact that a conical or flat seat with clearance tolerates some tilt before contact is forced. These factors reduce absolute moments and may reduce angular sensitivity in particular, since a tilted flat seat can leave a wedge-shaped gap that the screw does not fully close. The relation therefore gives an upper bound on the relative importance of angular misfit, and whether real joints approach it is the empirical question behind H16.

Combining error sources

If capture, design, and manufacturing errors are independent, their standard uncertainties combine in quadrature [43]:

σ_total^2 = σ_capture^2 + σ_design^2 + σ_manufacture^2 (8)

applied separately to distance and to angle. The design term covers library alignment and the definition of the interface geometry in software; the manufacturing term covers milling or printing and any post-processing. The budget shows where improvement is worthwhile: halving a component that contributes a fifth of the total variance changes the total very little.

6. Methodology

Review methods

The review is a critical narrative synthesis of systematic reviews and of laboratory studies selected for their methodological relevance. It is not a systematic review; recent meta-analyses are cited for pooled comparisons.

Part A: repeatability and reproducibility of capture

Reference object. A metal model of an edentulous arch carries six implant analogs with multi-unit abutments, arranged with inter-implant distances from about 10 to 45 mm and with relative axis divergences from 0 to 30 degrees. A second model with four analogs represents the common four-implant configuration. Models are machined from a dimensionally stable alloy and kept at controlled temperature.

Reference measurement. Platform centers and axes are measured with a tactile coordinate measuring machine whose maximum permissible error is stated and whose expanded uncertainty for the derived distances and angles is estimated and reported; the reference uncertainty should be no more than one quarter of the smallest difference the study aims to detect. Desktop optical scanners are not used as the reference.

Methods compared. Two intraoral scanners, each with two scan strategies and with and without an auxiliary reference device; two photogrammetric systems; and the splinted open-tray impression poured in type IV stone and measured on the same coordinate measuring machine. Scan bodies and targets are new and seated to a specified torque.

Design. Following the standard for interlaboratory accuracy experiments [39], three trained operators each make ten records with each method on each model, in randomized order across three sessions, removing and replacing scan bodies between records so that seating variation is included. Repeatability is estimated within operator and session, reproducibility across operators and sessions.

Analysis. Each record is reduced to platform points and axes by fitting the library geometry to each scan body or target individually. Inter-implant distance and angle errors (Equations 1 and 2) are computed for all pairs without global alignment. Trueness and precision are modeled as functions of true inter-implant distance with mixed-effects regression, with method as a fixed effect and operator and session as random effects. For comparison with the existing literature only, conventional best-fit root-mean-square deviations are also computed and the difference between the two reporting approaches is quantified.

Part B: imposed-error frameworks

Specimens. Titanium frameworks of constant cross-section are milled for the four-implant model. One series is nominal. In the others the seat for one terminal implant is machined with an imposed error: a vertical offset, a horizontal offset along the arch, or a tilt about a horizontal axis, each at four levels spanning the ranges observed in Part A, and in combination according to a response-surface design. The imposed geometry of every framework is verified on the coordinate measuring machine before testing.

Instrumentation. Strain gauges are bonded to the framework on each inter-implant segment, top and bottom, to resolve bending, and to the necks of the implant analogs, which are mounted in a block of bone-analog material of defined modulus. Screw preload is monitored with an instrumented screw or by ultrasonic elongation on a subsample.

Procedure. Screws are tightened in a fixed sequence to the manufacturer's torque with a calibrated driver; strains are recorded after each screw and at completion; the procedure is repeated five times per framework with new screws. The one-screw test, in which a single terminal screw is tightened and the lift at the opposite end observed, is performed and photographed as the clinical comparator [3].

Outcome and analysis. The primary outcome is peak principal strain in the framework at full tightening. A regression of peak strain on the imposed linear and angular errors and their interaction yields the proportion of variance attributable to each, with bootstrap confidence intervals; H16 is evaluated on the difference. Secondary outcomes are implant-neck strain, residual preload, and detection by the one-screw test.

Table 1. Error sources along the complete-arch digital workflow and how each is measured in the proposed protocol.
StageError sourceMeasurement in protocol
CaptureStitching accumulation; scan-body seating; library fit; target localizationPart A inter-implant distance and angle errors against coordinate measuring machine
DesignLibrary alignment tolerance; interface definition; software exportComparison of exported interface poses with captured poses
ManufactureTool wear and deflection; sintering or printing distortion; finishingCoordinate measurement of framework seats
AssemblySeat geometry and clearance; screw preload scatter; tightening sequencePart B strain and preload under imposed error

Sample size

Part A yields 30 records per method per model and 15 inter-implant pairs on the six-implant model, which is sufficient to estimate repeatability standard deviations with a relative uncertainty of roughly 15 percent; reproducibility across three operators is estimated less precisely, and the number of operators is the limiting factor. Part B, with five replicate tightenings on about 25 frameworks, is sized to estimate main effects and the linear-by-angular interaction in a second-order model; a formal power calculation requires the strain variance from pilot tightenings.

7. Evidence Synthesis and Explicitly Labeled Theoretical Predictions

Synthesis

Table 2 summarizes what the reviewed evidence supports. The comparison of capture methods rests almost entirely on laboratory studies of models. Heterogeneity among them is large, as would be expected when devices, software versions, scan bodies, references, and analysis methods all differ. The meta-analytic finding in favor of photogrammetry [32] is credible as a statement about position deviation on models; its magnitude, a few hundredths of a millimeter, is of the same order as the uncertainty of many of the references used.

Table 2. Statements about complete-arch implant records and the evidence supporting them.
StatementEvidenceLimitation
Splinted open-tray impressions are the most accurate conventional technique [8]Systematic review of mainly laboratory studiesNot a reference standard; stone and jig errors
Intraoral scan error increases with scanned distance [10, 13, 14]Laboratory and in vivo method studiesDevice- and strategy-specific
Photogrammetry has smaller deviations than intraoral scanning in complete arches [32–34]Meta-analyses of predominantly in vitro studiesHigh heterogeneity; best-fit metrics; no clinical outcomes
Auxiliary references and calibrated protocols reduce intraoral scan error [22, 24]Laboratory studiesFew studies; clinical practicality untested
Short-span milled frameworks are more precise than long-span, all within acceptable values [37]Laboratory studyOne manufacturing system
Framework misfit of the order of 100 µm was not associated with bone loss [4]Clinical observational studyCast frameworks; small sample; bone outcome only

Theoretical predictions

The following are deductions from Section 5 and have not been tested.

Prediction 1. For errors of the magnitudes commonly reported, tens of micrometers in distance and several tenths of a degree in angle, the idealized moment due to angular error exceeds that due to linear error for spans above about 10 mm (Equations 5 and 6). Measured strain will show a smaller ratio than the idealization because of joint compliance.

Prediction 2. Methods that differ little in best-fit root-mean-square deviation may differ substantially in cross-arch distance error, and their ranking by the two metrics will not always agree.

Prediction 3. For intraoral scans, distance error will increase with inter-implant distance while angle error will depend mainly on scan-body capture and be nearly independent of distance; for photogrammetry neither will depend strongly on distance.

Prediction 4. Platform position error will correlate with scan-body angular error with a slope close to the scan-body reference height (Equation 4).

Prediction 5. The one-screw test will detect vertical offsets at the far end more readily than tilts of the same mechanical consequence, since a tilt at a seated screw produces little lift elsewhere. If so, a clinically passing one-screw test does not exclude angular misfit.

8. Discussion: Mechanisms and Competing Explanations

The proposal rests on a mechanical argument that could be wrong in practice, and the alternatives are worth stating.

The first alternative is that linear error dominates because joints are far more tolerant of tilt than a fixed-end beam model implies. Multi-unit abutment seats are short cones or flats with clearance around the screw; a tilt of half a degree across a seat a few millimeters wide corresponds to a wedge of some tens of micrometers at its edge, which the prosthetic screw may not close. The framework then rests on one edge, the screw bends, and little moment is transmitted to the framework. Under this account, strain would follow vertical and horizontal offsets and H16 would fail, although screw bending might emerge as the relevant consequence of angular error, with implications for screw loosening and fracture and not for framework strain.

The second alternative is that neither matters within the range produced by competent current methods, because total error is absorbed by system compliance without consequence. The clinical observation that misfits of about 100 µm were not associated with bone loss [4] and the primate experiment [5] are consistent with considerable biological tolerance. Tolerance of bone is, however, a different matter from tolerance of screws and veneering materials over millions of load cycles, and the technical complication record of complete-arch prostheses [7] suggests that the mechanical system is not operating with unlimited margin.

The third alternative is that manufacturing and design, and not capture, dominate the error budget, in which case the comparison of capture devices that occupies most of the literature addresses a minor term. Equation 8 makes this testable, and Part A and the measurement of the milled seats provide the terms.

On measurement, the argument for frame-invariant metrics does not depend on H16. Whatever the mechanics, a deviation figure that changes with the alignment algorithm is a poor basis for comparing devices [41], and inter-implant distances and angles can be computed from data that most studies already hold. The earlier proposal of tolerances for inter-implant distance and angulation [42] took this approach; what has been missing is a mechanical basis for the tolerances.

The correlation between angular and linear error at capture (Equation 4) complicates interpretation of observational data. A device with poor scan-body orientation will show both errors, and regression on observed errors cannot separate them. This is why Part B imposes errors by machining, where they can be varied independently.

A further consideration is the mixing of data sources. Photogrammetry records implants but not tissue, and the merged dataset inherits registration error between two acquisitions. That error affects the relation of the prosthesis to the mucosa and the occlusion and does not affect framework fit; it is outside the present scope but belongs in any complete account of workflow accuracy.

9. Implications for Implant Prosthodontics

The practical conclusions that the present evidence supports are limited. For complete-arch records, laboratory data favor photogrammetry or reference-assisted scanning over unaided intraoral scanning, and the splinted conventional impression remains a legitimate standard. No method has been shown to improve clinical outcomes over another. Verification of fit before definitive manufacture, by a jig or a prototype, remains prudent whatever the capture method, since it tests the whole chain including manufacture.

If the angular hypothesis is correct, several habits would deserve revision. Scan bodies would be chosen for orientation fidelity and seating repeatability as well as ease of capture; accuracy claims would be expected to include angular error; and the one-screw test would be understood to be insensitive to a class of misfit. If the hypothesis is refuted, attention would properly return to cross-arch distance and to vertical discrepancy.

When reading accuracy studies, clinicians can ask four questions: what was the reference and how accurate was it; was deviation computed after best-fit alignment; were angular errors reported; and were different operators and sessions included.

10. Technical and Clinical Limitations

The mechanical analysis is an idealization of a two-implant segment and omits joint compliance, three-dimensional coupling in a curved arch, and the redistribution that occurs as successive screws are tightened. The laboratory protocol uses rigid models at controlled temperature and omits saliva, blood, soft-tissue mobility, limited access, and patient movement, all of which degrade intraoral capture more than laboratory figures suggest and may affect methods unequally. Devices and software change frequently, so device-specific results date quickly; the framework is intended to outlast them. Strain at tightening is a surrogate for technical complications and has not been linked quantitatively to them. Titanium frameworks of constant section do not represent monolithic zirconia or polymer prostheses, whose stiffness and failure behavior differ. The review is not systematic and may omit relevant studies.

11. Proposed Experimental and Clinical Validation

The laboratory program in Section 6 is the first stage. Its success criteria are an expanded reference uncertainty below one quarter of the smallest between-method difference of interest, and verified independence of imposed linear and angular errors in the machined frameworks. The second stage extends Part B to cyclic loading of frameworks with imposed misfit, with screw loosening and preload loss as outcomes, to connect tightening strain to a technical complication. The third stage is clinical and observational: in patients receiving complete-arch prostheses, the pose record from the digital method is compared with poses derived from a splinted verification jig measured on a coordinate measuring machine, giving in vivo inter-implant distance and angle errors, and technical complications are recorded prospectively and reported according to STROBE [44]. Such a study could relate measured pose error to complications, which no existing study does, though it would need several hundred prostheses and years of follow-up to do so.

H16 is rejected if the variance in peak strain attributable to linear error exceeds that attributable to angular error with a confidence interval for the difference excluding zero.

12. Future Research Directions

A shared physical reference object, circulated among laboratories in the manner of an interlaboratory comparison, would allow dental accuracy studies to be placed on a common scale and would expose the contribution of each laboratory's reference measurement. Finite element models of specific abutment seats, validated against Part B, could map the tolerance of each connection design to tilt and offset. Per-case uncertainty estimation, in which the capture system reports a confidence region for each implant pose, would let the clinician decide when verification is needed; the appendix outlines one possible approach. The behavior of printed and milled polymer prototypes as fit-verification devices, given their low stiffness, is a practical question that the pose-error framework could address.

13. Evidence-Calibrated Conclusion

Laboratory evidence of moderate consistency indicates that photogrammetry yields smaller implant-position deviations than intraoral scanning in complete-arch models, and that intraoral scan error grows with scanned distance. No clinical evidence shows that any capture method changes prosthetic outcomes, and no threshold of acceptable misfit has been validated. The reporting of accuracy by best-fit surface deviation is poorly suited to the prosthodontic question. Inter-implant distance and angle errors are frame-invariant alternatives that can be computed from existing data. Beam theory suggests that angular error is mechanically more important than its neglect in the literature would imply; that suggestion is theoretical, depends on joint behavior that the idealization omits, and is put forward here with the experiment that could refute it.

Cite this paper

Jain S, Gupta A. Which Error Matters in Complete-Arch Digital Implant Records? A Pose-Based Metrology Framework for Intraoral Scanning and Photogrammetry and a Test of the Angular-Error Hypothesis of Prosthesis Misfit. Working paper. Center for Implant Dentistry; 2026. Available from: https://bayareaimplantdentistry.com/clinician-research-and-publications/pose-based-metrology-for-complete-arch-implant-records

References

  1. Sahin S, Cehreli MC. The significance of passive framework fit in implant prosthodontics: current status. Implant Dent. 2001;10(2):85-92. doi:10.1097/00008505-200104000-00003 (opens in a new tab) PMID: 11450418 (opens in a new tab).
  2. Abduo J, Bennani V, Waddell N, Lyons K, Swain M. Assessing the fit of implant fixed prostheses: a critical review. Int J Oral Maxillofac Implants. 2010;25(3):506-15. PMID: 20556249 (opens in a new tab).
  3. Kan JY, Rungcharassaeng K, Bohsali K, Goodacre CJ, Lang BR. Clinical methods for evaluating implant framework fit. J Prosthet Dent. 1999;81(1):7-13. doi:10.1016/s0022-3913(99)70229-5 (opens in a new tab) PMID: 9878969 (opens in a new tab).
  4. Jemt T, Book K. Prosthesis misfit and marginal bone loss in edentulous implant patients. Int J Oral Maxillofac Implants. 1996;11(5):620-5. PMID: 8908860 (opens in a new tab).
  5. Carr AB, Gerard DA, Larsen PE. The response of bone in primates around unloaded dental implants supporting prostheses with different levels of fit. J Prosthet Dent. 1996;76(5):500-9. doi:10.1016/s0022-3913(96)90008-6 (opens in a new tab) PMID: 8933440 (opens in a new tab).
  6. Katsoulis J, Takeichi T, Sol Gaviria A, Peter L, Katsoulis K. Misfit of implant prostheses and its impact on clinical outcomes. Definition, assessment and a systematic review of the literature. Eur J Oral Implantol. 2017;10 Suppl 1:121-138. PMID: 28944373 (opens in a new tab).
  7. Papaspyridakos P, Chen CJ, Chuang SK, Weber HP, Gallucci GO. A systematic review of biologic and technical complications with fixed implant rehabilitations for edentulous patients. Int J Oral Maxillofac Implants. 2012;27(1):102-10. PMID: 22299086 (opens in a new tab).
  8. Papaspyridakos P, Chen CJ, Gallucci GO, Doukoudakis A, Weber HP, Chronopoulos V. Accuracy of implant impressions for partially and completely edentulous patients: a systematic review. Int J Oral Maxillofac Implants. 2014;29(4):836-45. doi:10.11607/jomi.3625 (opens in a new tab) PMID: 25032763 (opens in a new tab).
  9. Mangano F, Gandolfi A, Luongo G, Logozzo S. Intraoral scanners in dentistry: a review of the current literature. BMC Oral Health. 2017;17(1):149. doi:10.1186/s12903-017-0442-x (opens in a new tab) PMID: 29233132 (opens in a new tab).
  10. Ender A, Mehl A. Accuracy of complete-arch dental impressions: a new method of measuring trueness and precision. J Prosthet Dent. 2013;109(2):121-8. doi:10.1016/S0022-3913(13)60028-1 (opens in a new tab) PMID: 23395338 (opens in a new tab).
  11. Ender A, Attin T, Mehl A. In vivo precision of conventional and digital methods of obtaining complete-arch dental impressions. J Prosthet Dent. 2016;115(3):313-20. doi:10.1016/j.prosdent.2015.09.011 (opens in a new tab) PMID: 26548890 (opens in a new tab).
  12. Nedelcu R, Olsson P, Nyström I, Rydén J, Thor A. Accuracy and precision of 3 intraoral scanners and accuracy of conventional impressions: A novel in vivo analysis method. J Dent. 2018;69:110-118. doi:10.1016/j.jdent.2017.12.006 (opens in a new tab) PMID: 29246490 (opens in a new tab).
  13. Iturrate M, Amezua X, Garikano X, Solaberrieta E. Use of measuring gauges for in vivo accuracy analysis of intraoral scanners: a pilot study. J Adv Prosthodont. 2021;13(4):191-204. doi:10.4047/jap.2021.13.4.191 (opens in a new tab) PMID: 34504671 (opens in a new tab).
  14. Giménez B, Özcan M, Martínez-Rus F, Pradíes G. Accuracy of a digital impression system based on parallel confocal laser technology for implants with consideration of operator experience and implant angulation and depth. Int J Oral Maxillofac Implants. 2014;29(4):853-62. doi:10.11607/jomi.3343 (opens in a new tab) PMID: 25032765 (opens in a new tab).
  15. Vandeweghe S, Vervack V, Dierens M, De Bruyn H. Accuracy of digital impressions of multiple dental implants: an in vitro study. Clin Oral Implants Res. 2017;28(6):648-653. doi:10.1111/clr.12853 (opens in a new tab) PMID: 27150731 (opens in a new tab).
  16. Flügge T, van der Meer WJ, Gonzalez BG, Vach K, Wismeijer D, Wang P. The accuracy of different dental impression techniques for implant-supported dental prostheses: A systematic review and meta-analysis. Clin Oral Implants Res. 2018;29 Suppl 16:374-392. doi:10.1111/clr.13273 (opens in a new tab) PMID: 30328182 (opens in a new tab).
  17. Papaspyridakos P, Vazouras K, Chen YW, Kotina E, Natto Z, Kang K, et al. Digital vs Conventional Implant Impressions: A Systematic Review and Meta-Analysis. J Prosthodont. 2020;29(8):660-678. doi:10.1111/jopr.13211 (opens in a new tab) PMID: 32613641 (opens in a new tab).
  18. Wulfman C, Naveau A, Rignon-Bret C. Digital scanning for complete-arch implant-supported restorations: A systematic review. J Prosthet Dent. 2020;124(2):161-167. doi:10.1016/j.prosdent.2019.06.014 (opens in a new tab) PMID: 31757443 (opens in a new tab).
  19. Zhang YJ, Shi JY, Qian SJ, Qiao SC, Lai HC. Accuracy of full-arch digital implant impressions taken using intraoral scanners and related variables: A systematic review. Int J Oral Implantol (Berl). 2021;14(2):157-179. PMID: 34006079 (opens in a new tab).
  20. Papaspyridakos P, Gallucci GO, Chen CJ, Hanssen S, Naert I, Vandenberghe B. Digital versus conventional implant impressions for edentulous patients: accuracy outcomes. Clin Oral Implants Res. 2016;27(4):465-72. doi:10.1111/clr.12567 (opens in a new tab) PMID: 25682892 (opens in a new tab).
  21. Mizumoto RM, Yilmaz B. Intraoral scan bodies in implant dentistry: A systematic review. J Prosthet Dent. 2018;120(3):343-352. doi:10.1016/j.prosdent.2017.10.029 (opens in a new tab) PMID: 29627211 (opens in a new tab).
  22. Iturrate M, Eguiraun H, Etxaniz O, Solaberrieta E. Accuracy analysis of complete-arch digital scans in edentulous arches when using an auxiliary geometric device. J Prosthet Dent. 2019;121(3):447-454. doi:10.1016/j.prosdent.2018.09.017 (opens in a new tab) PMID: 30554826 (opens in a new tab).
  23. Mizumoto RM, Yilmaz B, McGlumphy EA Jr, Seidt J, Johnston WM. Accuracy of different digital scanning techniques and scan bodies for complete-arch implant-supported prostheses. J Prosthet Dent. 2020;123(1):96-104. doi:10.1016/j.prosdent.2019.01.003 (opens in a new tab) PMID: 31040026 (opens in a new tab).
  24. Li J, Chen Z, Nava P, Yang S, Calatrava J, Wang HL. Calibrated intraoral scan protocol (CISP) for full-arch implant impressions: An in vitro comparison to conventional impression, intraoral scan, and intraoral scan with scan-aid. Clin Implant Dent Relat Res. 2024;26(5):879-888. doi:10.1111/cid.13338 (opens in a new tab) PMID: 38747500 (opens in a new tab).
  25. Lie A, Jemt T. Photogrammetric measurements of implant positions. Description of a technique to determine the fit between implants and superstructures. Clin Oral Implants Res. 1994;5(1):30-6. doi:10.1034/j.1600-0501.1994.050104.x (opens in a new tab) PMID: 8038342 (opens in a new tab).
  26. Jemt T, Lie A. Accuracy of implant-supported prostheses in the edentulous jaw: analysis of precision of fit between cast gold-alloy frameworks and master casts by means of a three-dimensional photogrammetric technique. Clin Oral Implants Res. 1995;6(3):172-80. doi:10.1034/j.1600-0501.1995.060306.x (opens in a new tab) PMID: 7578793 (opens in a new tab).
  27. Peñarrocha-Oltra D, Agustín-Panadero R, Bagán L, Giménez B, Peñarrocha M. Impression of multiple implants using photogrammetry: description of technique and case presentation. Med Oral Patol Oral Cir Bucal. 2014;19(4):e366-71. doi:10.4317/medoral.19365 (opens in a new tab) PMID: 24608216 (opens in a new tab).
  28. Sánchez-Monescillo A, Sánchez-Turrión A, Vellon-Domarco E, Salinas-Goodier C, Prados-Frutos JC. Photogrammetry Impression Technique: A Case History Report. Int J Prosthodont. 2016;29(1):71-3. doi:10.11607/ijp.4287 (opens in a new tab) PMID: 26757333 (opens in a new tab).
  29. Revilla-León M, Att W, Özcan M, Rubenstein J. Comparison of conventional, photogrammetry, and intraoral scanning accuracy of complete-arch implant impression procedures evaluated with a coordinate measuring machine. J Prosthet Dent. 2021;125(3):470-478. doi:10.1016/j.prosdent.2020.03.005 (opens in a new tab) PMID: 32386912 (opens in a new tab).
  30. Tohme H, Lawand G, Chmielewska M, Makhzoume J. Comparison between stereophotogrammetric, digital, and conventional impression techniques in implant-supported fixed complete arch prostheses: An in vitro study. J Prosthet Dent. 2023;129(2):354-362. doi:10.1016/j.prosdent.2021.05.006 (opens in a new tab) PMID: 34112521 (opens in a new tab).
  31. Ma B, Yue X, Sun Y, Peng L, Geng W. Accuracy of photogrammetry, intraoral scanning, and conventional impression techniques for complete-arch implant rehabilitation: an in vitro comparative study. BMC Oral Health. 2021;21(1):636. doi:10.1186/s12903-021-02005-0 (opens in a new tab) PMID: 34893053 (opens in a new tab).
  32. Pozzi A, Arcuri L, Carosi P, Laureti A, Londono J, Wang HL. Photogrammetry Versus Intraoral Scanning in Complete-Arch Digital Implant Impression: A Systematic Review and Meta-Analysis. Clin Implant Dent Relat Res. 2025;27(3):e70059. doi:10.1111/cid.70059 (opens in a new tab) PMID: 40481748 (opens in a new tab).
  33. Jain S, Daak HA, Someli LA, Alamer AY, Apratim A, Akoor RMA, et al. Accuracy of Stereophotogrammetry Technique versus Intraoral Scanners for Complete-Arch Implant Digital Impressions: A Systematic Review and Meta-Analysis. Eur J Dent. 2026;20(1):34-48. doi:10.1055/s-0045-1806935 (opens in a new tab) PMID: 40311637 (opens in a new tab).
  34. Noronha CP, Ferreira de Souza C, Dantas Dos Santos Oliveira M, Silva EVFD, Sesma N, Mukai MK. Accuracy of Stereophotogrammetry in Implant Scanning Compared to Intraoral Scanning in Completely Edentulous Patients-A Systematic Review and Meta-analysis. Int J Prosthodont. 2026;39(3):397-404. doi:10.11607/ijp.9358 (opens in a new tab) PMID: 40694393 (opens in a new tab).
  35. Revilla-León M, Özcan M. Additive Manufacturing Technologies Used for Processing Polymers: Current Status and Potential Application in Prosthetic Dentistry. J Prosthodont. 2019;28(2):146-158. doi:10.1111/jopr.12801 (opens in a new tab) PMID: 29682823 (opens in a new tab).
  36. Ortorp A, Jemt T, Bäck T, Jälevik T. Comparisons of precision of fit between cast and CNC-milled titanium implant frameworks for the edentulous mandible. Int J Prosthodont. 2003;16(2):194-200. PMID: 12737254 (opens in a new tab).
  37. Katsoulis J, Müller P, Mericske-Stern R, Blatz MB. CAD/CAM fabrication accuracy of long- vs. short-span implant-supported FDPs. Clin Oral Implants Res. 2015;26(3):245-9. doi:10.1111/clr.12522 (opens in a new tab) PMID: 25363301 (opens in a new tab).
  38. Abduo J, Lyons K, Bennani V, Waddell N, Swain M. Fit of screw-retained fixed implant frameworks fabricated by different methods: a systematic review. Int J Prosthodont. 2011;24(3):207-20. PMID: 21519567 (opens in a new tab).
  39. International Organization for Standardization. ISO 5725-1: Accuracy (trueness and precision) of measurement methods and results - Part 1: General principles and definitions. Geneva: ISO. †
  40. International Organization for Standardization. ISO 20896-1: Dentistry - Digital impression devices - Part 1: Methods for assessing accuracy. Geneva: ISO; 2019. †
  41. O'Toole S, Osnes C, Bartlett D, Keeling A. Investigation into the accuracy and measurement methods of sequential 3D dental scan alignment. Dent Mater. 2019;35(3):495-500. doi:10.1016/j.dental.2019.01.012 (opens in a new tab) PMID: 30683418 (opens in a new tab).
  42. Andriessen FS, Rijkens DR, van der Meer WJ, Wismeijer DW. Applicability and accuracy of an intraoral scanner for scanning multiple implants in edentulous mandibles: a pilot study. J Prosthet Dent. 2014;111(3):186-94. doi:10.1016/j.prosdent.2013.07.010 (opens in a new tab) PMID: 24210732 (opens in a new tab).
  43. Joint Committee for Guides in Metrology. Evaluation of measurement data - Guide to the expression of uncertainty in measurement (JCGM 100:2008). Sevres: BIPM; 2008. †
  44. von Elm E, Altman DG, Egger M, Pocock SJ, Gøtzsche PC, Vandenbroucke JP, et al. The Strengthening the Reporting of Observational Studies in Epidemiology (STROBE) statement: guidelines for reporting observational studies. Lancet. 2007;370(9596):1453-7. doi:10.1016/S0140-6736(07)61602-X (opens in a new tab) PMID: 18064739 (opens in a new tab).
  45. Nobel Biocare AB, assignee. Method of manufacturing a prosthesis to be fixed to implants in the jawbone of a patient, and a system for manufacturing such prostheses. United States patent US 5,857,853. 1999 Jan 12. ‡
  46. United States patent US 6,287,119 B1 (same patent family as US 5,857,853). ‡
  47. Method and system for real time intra-orally acquiring and registering three-dimensional measurements and images of intra-oral objects and features. United States patent US 6,402,707. ‡
  48. System and method for improved intra-oral scanning protocol and calibration. International patent application WO 2013/158432 A1. ‡
  49. Canadian patent document CA 3,086,482 (gauge for correcting stitched intraoral scans; title as recorded in the Canadian Patents Database to be confirmed). ‡
  50. Reference verification note. 41 of 49 references are PubMed-indexed; their bibliographic records (authors, title, journal, year, volume, pages, DOI, PMID) were retrieved programmatically from the PubMed database on November 17, 2026. ‡ Standard, regulatory record or patent whose identifying details were confirmed against the issuing body’s public record during the research phase. † Source not indexed in PubMed (book, standard, guidance or non-indexed journal); bibliographic details are cited from the published record and were not database-verified in this drafting session. Database retrieval confirms that each record exists as cited; it does not replace full-text reading by the responsible authors of every statement attributed to a source.