Beyond Peak Temperature: A Spatiotemporal Thermal-Dose Model Linking Implant Osteotomy Heating to Microvascular Injury and Early Osseointegration
- Paper type
- Mechanistic research framework and laboratory validation protocol
- Status
- Original Work · Working Paper
Contents
Abstract
Background. The safety of implant site preparation is judged against a temperature threshold of 47 °C for one minute that derives from vital-microscopic observations in rabbit bone. Later animal studies report thresholds from 47 °C to 55 °C and show that heating to 60 °C for one minute does not impair osseointegration in dense bone yet reduces bone-to-implant contact in low-density bone. A single peak temperature cannot reconcile these findings.
Objective. To formulate a model in which the biological effect of osteotomy heating is determined by the cumulative thermal dose retained in the bone that remains after the final drill, with separate dose–response relations for microvascular and osteocytic compartments, and to specify experiments that can discriminate this model from a peak-temperature model.
Framework. Transient heat conduction with a moving drill source yields a temperature history at every point. Thermal dose is computed as cumulative equivalent minutes at 43 °C and, in parallel, as Arrhenius damage integrals for endothelial and osteocytic populations. Because each drill removes bone heated by its predecessor, the relevant quantity is the dose field outside the final osteotomy wall. A devascularized annulus of width w_d delays bone formation at the implant surface by the time required for revascularization.
Proposed validation. Three stages: ex vivo mapping of temperature fields and calibration of the conduction model; in vitro time–temperature survival surfaces for endothelial cells, osteocyte-like cells, and osteoprogenitors; and an in vivo experiment with a design that crosses peak temperature and thermal dose so that the two predictors are not collinear.
Central hypothesis. Retained thermal dose predicts perfusion loss and early bone-to-implant contact better than peak temperature, and microvascular injury extends beyond the zone of histologically evident osteocyte necrosis.
Conclusions. The framework is proposed and untested. Simple arithmetic on published thresholds shows that they span four orders of magnitude in equivalent thermal dose, which indicates that they do not describe a single biological endpoint. No experimental results are reported.
Keywords: osteotomy; thermal injury; thermal dose; bone microvasculature; angiogenesis; osseointegration; bioheat transfer; finite element analysis
1. Introduction
Every implant osteotomy heats the bone it cuts. The clinical response has been to keep the bone cool with sharp drills, low loads, intermittent motion, and irrigation, and to judge success against a threshold. The threshold, 47 °C for one minute, comes from experiments in which a thermal chamber implanted in the rabbit tibia allowed direct observation of living bone and its vessels during controlled heating [1]. It has guided drill design and surgical technique for forty years [2–4].
The threshold has two properties that limit its use. It is a single point on what must be a time–temperature surface: no one supposes that 46 °C for ten minutes is safe because it is below 47 °C, or that 49 °C for two seconds is harmful because it is above. And it was defined by what could be seen through a vital microscope, which was largely vascular: arrest of flow, dilation, and later resorption of the observed tissue. A companion study from the same group found that vital microscopy showed consistent and widespread injury after heating to 50 °C for one minute while histological and histochemical methods were less revealing [5]. The threshold on which the field relies is therefore, in origin, a threshold for microvascular events, yet it is applied to measurements of peak temperature at a thermocouple and interpreted as a boundary for bone necrosis.
Subsequent animal studies have not converged. A systematic review of preclinical in vivo studies placed the threshold for thermal necrosis between 47 °C and 55 °C for one minute [6]. In dense bone, heating the osteotomy to as much as 60 °C for one minute did not significantly impair osseointegration [7]. In low-density bone, the same exposure did not cause implant failure but was associated with crestal bone loss and lower bone-to-implant contact [8]. In cell culture, exposures of 45 °C and 47 °C produced an immediate necrotic response, yet mild heat shock at or below 47 °C for durations typical of surgical cutting enhanced the osteogenic behavior of progenitors [9]. These observations are difficult to reconcile if the governing variable is peak temperature and the endpoint is cell death.
The proposal made here is that two changes of variable resolve much of the inconsistency. The first replaces peak temperature with cumulative thermal dose, a quantity with a long history in hyperthermia research [10–12]. The second replaces the single endpoint with at least two tissue compartments, microvascular and osteocytic, that need not share a dose–response relation. A third consideration is spatial. Implant sites are prepared with a sequence of drills, and each drill removes bone that its predecessor heated. The dose that matters biologically is the dose retained in the bone that will face the implant.
This manuscript develops these ideas into a model, derives predictions that differ from those of a peak-temperature criterion, and describes a laboratory program to test them. The observation that heat injures bone vessels is as old as the threshold itself. What has not been done, in the literature identified, is to model the vascular compartment explicitly, to couple it to the time course of early bone formation, and to design an experiment in which dose and peak temperature are separated.
2. Background and Current Scientific Evidence
Origin and meaning of the 47 °C threshold
Eriksson and Albrektsson heated rabbit bone through an implanted optical chamber and followed the tissue over weeks [1]. Related work measured heat generated by drilling cortical bone in patients and animals [13] and recorded temperatures during drilling for implant placement in five edentulous human mandibles with a thermocouple positioned 0.5 mm from the drill surface [14]. Earlier, Lundskog had characterized the thermal properties of bone and its response to heat [15]. The methodological point from this body of work that has been least absorbed is the one made in the 1984 comparison: observation of living tissue detected injury that conventional histology and histochemistry did not [5]. If the most sensitive indicator of thermal injury in bone is vascular, then histomorphometric endpoints assessed weeks later, such as bone-to-implant contact, are integrating over a healing process that the vascular injury has modified, and they should be expected to depend on site vascularity and healing capacity as well as on the thermal insult.
Variability of reported thresholds
The systematic review by Kniha and colleagues, undertaken to inform thermal explantation of implants, included 25 animal studies and reported necrosis thresholds of 47–55 °C for one minute, with bone-to-implant contact significantly reduced at 50 °C for one minute [6]. The pair of studies by Trisi and colleagues is the clearest demonstration that outcome depends on the bone as well as on the heat: similar exposures were tolerated in dense bone and were detrimental to marginal bone and bone-to-implant contact in low-density bone [7, 8]. A recent systematic review of histological and histomorphometric studies of implant bed preparation concluded that methods are too heterogeneous to identify optimal parameters and called for uniform methodology [16].
What is measured in drilling studies
Most studies of drilling heat report the maximum temperature rise at one or a few thermocouples, or the maximum on an infrared image of an exposed surface. A systematic review of heat generation and drill wear counted thermocouples in 18 studies and infrared thermography in 7 [4]. External irrigation kept bone below 47 °C across all parameter combinations in one experimental series [3]; irrigation, interval drilling, and drill geometry each reduce temperature elevation [17]. Recent bench studies continue to compare drill designs by peak temperature [18]. Neither the duration above a given temperature nor the spatial extent of heating is routinely reported, and the thermocouple’s distance from the cutting surface, which determines what it records, varies among studies.
Models of drilling heat and of thermal damage
Thermal models of bone drilling partition cutting energy between chips, drill, and bone and solve the conduction problem in the bone [19]. Finite element and analytical approaches have been used to estimate the extent of thermal necrosis in cortical bone [20, 21]. The thermal conductivity of bovine cortical bone has been measured at 0.53–0.58 W/(m·K) depending on direction [22]. One study coupled a validated computational model of drilling temperatures in bone of different densities with a biological assessment of cell death after osteotomy [23], and an animal study related drill speed to osteocyte apoptosis and bone resorption while showing that trabecular bone healed faster than dense lamellar bone because of its larger population of Wnt-responsive osteoprogenitors [24]. A study in rat tibia combined numerical simulation with histomorphometry [25]. These are the closest precedents for the present proposal. They address osteocyte death. None, as far as their abstracts indicate, models the vascular compartment or separates dose from peak temperature experimentally.
Thermal damage in other tissues is conventionally described in two equivalent ways. The Arrhenius formulation, introduced for skin burns, integrates a temperature-dependent rate over time [26]. The cumulative-equivalent-minutes formulation converts any time–temperature history into the number of minutes at 43 °C that would produce the same effect [10]. Thresholds for damage expressed in this unit have been compiled for many normal tissues [11, 12]. As far as the search could determine, neither formulation has been calibrated for the microvasculature of bone.
Cellular responses to heat in bone
Osteocyte-like cells exposed to temperatures in the range produced by surgical cutting undergo apoptosis and necrosis and then release signals that are first pro-osteoclastogenic and later pro-osteoblastogenic [27]. Mild heat shock can be stimulatory to progenitors [9]. A thermal insult therefore has at least three regimes: a sub-injurious regime that may promote healing, an intermediate regime in which injured cells initiate remodeling, and a destructive regime in which tissue is lost. Where the boundaries lie on the time–temperature plane has not been mapped for the cell types that matter.
Vascular dependence of peri-implant bone formation
Early peri-implant healing proceeds from a coagulum through a provisional matrix to woven bone, and new vessels precede and accompany bone formation at each step [28–30]. In bone generally, a specific capillary subtype couples angiogenesis to osteogenesis by maintaining perivascular osteoprogenitors [31, 32], and angiogenesis is rate-limiting for repair [33]. The physiology of bone blood flow, and the difficulty of measuring it, have been reviewed [34]. It follows that a band of bone that is structurally intact but devascularized is not a neutral substrate. Bone formation at an implant surface that faces such a band must wait for vessels to cross it or for the band to be resorbed and replaced.
Summary
It is established that drilling heats bone, that sufficient heat kills bone cells and damages vessels, and that irrigation and technique limit the temperature rise. Evidence on where the threshold lies is inconsistent, and the inconsistency tracks differences in exposure time, endpoint, and bone type. Thermal-dose formalisms exist but have not been applied systematically to implant osteotomy. The vascular compartment was central to the original observations and has been largely absent from subsequent modeling.
3. Research Gap
Three specific gaps follow. No study identified here reports the spatial field of cumulative thermal dose around an implant osteotomy, as opposed to temperature at a point. No dose–response relation exists for thermal injury to bone microvascular endothelium over the time–temperature range of drilling, and no comparison of that relation with the one for osteocytes. And no in vivo experiment has been designed so that peak temperature and thermal dose vary independently, which is the only way to determine which is the better predictor of biological outcome.
A further gap is conceptual. Sequential drilling means that the thermal history of bone which is later removed is irrelevant to healing. Studies that report the peak temperature of the pilot drill, which often runs hottest, may be describing bone that no longer exists when the implant is placed. The quantity of interest has not been defined in the literature in a way that accounts for this.
4. Research Objective and Central Hypothesis
The objective is to construct and prepare for validation a spatiotemporal model that links osteotomy heating to microvascular injury and to the timing of early bone formation at the implant surface.
The central hypothesis has two parts. (H1) In an in vivo model, the cumulative thermal dose retained in bone beyond the final osteotomy wall predicts perfusion loss at 24–72 hours and bone-to-implant contact at 2 weeks better than the peak temperature recorded during preparation, as judged by prespecified measures of predictive performance. (H2) The radial extent of microvascular injury exceeds the radial extent of osteocyte lacunar emptying at matched time points; that is, a devascularized but structurally populated annulus exists.
Three secondary hypotheses are subordinate to these. The time–temperature survival surface of bone-derived endothelial cells differs from that of osteocyte-like cells. The delay in bone formation scales with the width of the devascularized annulus. And the adverse effect of a given retained dose is larger where early stability depends on new bone formation than where it is provided by existing dense bone.
Each hypothesis can fail. If peak temperature predicts outcomes as well as dose when the two are decorrelated, H1 is refuted. If vascular and osteocytic injury margins coincide, H2 is refuted and the two-compartment structure is unnecessary.
5. Scientific and Theoretical Framework
Temperature field
Within the bone domain, temperature T(x,t) obeys the bioheat equation [35]
ρc (∂T)/(∂t)=∇⋅(k∇T)+ω_b ρ_bc_b (T_a−T)+q_m (1)
where ρ is density (kg/m³), c specific heat (J/(kg·K)), k thermal conductivity (W/(m·K)), ω_b volumetric blood perfusion (m³ blood per m³ tissue per second), ρ_bc_b the volumetric heat capacity of blood, T_a arterial temperature, and q_m metabolic heat generation. Drilling enters as a moving heat flux q_d(t) on the instantaneous osteotomy wall and at the advancing tip, with the fraction of cutting power conducted into bone treated as a calibration parameter [19]. Irrigation is represented as a convective boundary condition with coefficient h_(irr) on wetted surfaces.
Two simplifications are justified by scale. A drilling step lasts seconds, and over that interval the perfusion and metabolic terms are small relative to conduction in cortical bone; they are retained for completeness and for the minutes that follow, when they govern cooling. Second, conductivity is treated as transversely isotropic with the measured directional values [22], and heterogeneity between cortical and cancellous regions is assigned from imaging.
Thermal dose
The thermal history at each point is converted to cumulative equivalent minutes at 43 °C [10]:
CEM43(x)=∫_0^t_f R^( 43−T(x,t)) dt, R=(0.5,T≥43 ^∘C0.25,T<43 ^∘C) (2)
with t in minutes and T in °C. The values of R are those of the original formulation, derived largely from cell-survival data in other tissues at temperatures up to the low 50s °C; their validity for bone and for the higher temperatures of drilling is an assumption to be tested in Stage B.
In parallel, compartment-specific Arrhenius integrals are defined [26]:
Ω_j(x)=∫_0^t_f A_jexp(−E_j/(R T_K(x,t)))dt, S_j=e^(−Ω_j) (3)
for j∈{v,o} (microvascular endothelium, osteocytes), with frequency factor A_j (s⁻¹), activation energy E_j (J/mol), universal gas constant R, absolute temperature T_K, and surviving fraction S_j. No values of A_j or E_j for bone are asserted here. They are the outputs of Stage B.
Retained dose under sequential drilling
Let the osteotomy be prepared by drills of radii r_1<r_2<…<r_n. Drill i deposits a dose increment ΔD_i(x) in the bone outside radius r_i. Bone at radial position r<r_n is removed before the implant is placed. The retained dose is the sum of increments over all steps, evaluated only where bone remains:
D_(ret)(x)=∑_i=1^n ΔD_i(x), ∥x∥_⊥≥r_n (4)
where ∥x∥_⊥ is distance from the osteotomy axis. A step contributes to D_(ret) only to the extent that its heat penetrates beyond r_n. A hot pilot drill followed by wide enlargement may contribute nothing; a hot final drill contributes fully. This is the sense in which the spatial distribution of exposure carries information that peak temperature lacks.
Injury margins and the devascularized annulus
Define the injury radius for compartment j as the largest radius at which survival falls below one half:
ρ_j=max{ r:S_j(r)<0.5 } (5)
The hypothesis H2 is ρ_v>ρ_o. The annulus between them, of width w_d=ρ_v−max(ρ_o,r_n), contains bone with viable osteocytes and non-perfused vessels. Bone inside ρ_o is necrotic and must be resorbed.
Coupling to bone formation
New bone at the implant surface requires a vascular supply within diffusion distance. If revascularization advances from intact tissue at a mean front speed v_a, the time at which bone formation can begin at the implant surface is delayed, relative to an uninjured site, by approximately
τ_d≈w_d/v_a+τ_r (6)
where τ_r accounts for resorption of any necrotic layer inside ρ_o. Neither v_a nor τ_r is known for peri-implant bone; equation (6) is a scaling relation that Stage C is designed to test, and it predicts that the delay is proportional to annulus width.
The relation also suggests why bone type should matter. Where an implant achieves stability by engaging existing dense bone, a delay in new bone formation costs little. Where stability must be built by new bone growing through trabecular spaces, a delay is paid for in early bone-to-implant contact. This offers one interpretation of why the same heating was tolerated in dense bone and not in low-density bone [7, 8], alongside the possibility that the less mineralized site simply heats to a greater depth for the same surface temperature. The two explanations make different predictions about the temperature field and can be distinguished.
6. Methodology
Stage A: ex vivo temperature-field mapping and model calibration
Specimens. Fresh bovine rib or porcine mandible segments, stratified by cortical thickness and cancellous density measured by micro-computed tomography, maintained at 37 °C in a saline bath.
Instrumentation. Thermocouple arrays at radial distances of 0.5, 1.0, 2.0, and 3.0 mm from the final osteotomy wall and at three depths, positioned with a drilling jig and verified by micro-computed tomography. Radial distance is referenced to the final wall, in keeping with equation (4). A split-specimen configuration with an infrared camera viewing the cut plane through an infrared-transparent window provides full-field data for a subset. Thrust force and torque are recorded.
Design. A fractional factorial over rotational speed, feed rate or axial load, irrigation (none, external, internal), drill condition (new, worn to a defined number of uses), sequence (pilot only; conventional sequence; single-step), and bone stratum. Each cell is replicated.
Model calibration and validation. A finite element model of equation (1) with a moving source is fitted to two thirds of the conditions by adjusting the heat partition fraction and h_(irr); the remaining third is predicted without adjustment. Mesh and time-step convergence are documented, and discretization uncertainty is estimated by systematic refinement [36]. Validation metrics are the error in peak temperature, in time above 43 °C, and in CEM43 at each sensor. Model credibility is assessed following ASME V&V 40 [37].
Output. Maps of D_(ret) for each condition, and the correlation across conditions between peak temperature at the conventional sensor location and D_(ret). If that correlation is near unity across all realistic conditions, dose adds little in practice whatever its theoretical merit, and this would be reported as a negative result.
Stage B: in vitro time–temperature survival surfaces
Cells. Primary bone-marrow or bone-derived microvascular endothelial cells; an osteocyte-like line as used in prior heat-shock work [9, 27]; and primary osteoprogenitors. Species matched to Stage C.
Exposure. Thin-walled vessels in a calibrated circulating bath or thermal cycler, with a thermocouple in a sham well to record the actual history. Temperatures from 43 °C to 60 °C in 2–3 °C steps; durations from 5 to 120 seconds, plus 5 minutes at the lower temperatures. Controls at 37 °C handled identically.
Endpoints. Viability and membrane integrity at 4, 24, and 72 hours; apoptosis by caspase activity and annexin staining; for endothelial cells, tube formation and sprouting capacity of survivors, which measures function and not only survival; for osteocyte-like cells, RANKL and OPG expression; for progenitors, proliferation and early osteogenic markers.
Analysis. For each cell type, survival is fitted to equation (3) to estimate A_j and E_j with confidence regions, and to equation (2) with R free. The hypothesis that endothelial and osteocytic parameters are equal is tested by likelihood ratio. The fitted surfaces define iso-survival contours on the time–temperature plane; the published thresholds can then be placed on that plane and their compartment-specific meaning read off.
Limitation acknowledged in design. Cells in culture lack the matrix, the marrow, and the flow of the tissue. Stage B provides relative sensitivities and the functional form. It does not provide in vivo thresholds.
Stage C: in vivo discrimination experiment
Model. Rabbit tibia or minipig mandible, the choice to be made on the feasibility of perfusion imaging and the relevance of bone architecture; reporting follows ARRIVE 2.0 [38].
Heating. To control the thermal history independently of cutting mechanics, osteotomies are prepared under copious irrigation to a standard diameter and then heated with a temperature-controlled probe of matching diameter for a programmed time–temperature profile, as in earlier threshold studies [7, 8]. A separate arm uses actual drilling protocols selected from Stage A to span the range of D_(ret), to confirm that findings transfer from probe heating to drilling.
Design. The probe arm crosses peak temperature with dose (Table 2). Conditions are chosen so that some pairs share a peak temperature and differ in CEM43 by a large factor, and other pairs share CEM43 and differ in peak temperature. This decorrelation is the central feature of the experiment.
| Condition | Peak temperature | Duration | CEM43 (min) | Purpose |
|---|---|---|---|---|
| C0 | 37 °C | 60 s | — | Sham control |
| C1 | 47 °C | 15 s | 4 | Low dose at the classical threshold temperature |
| C2 | 47 °C | 240 s | 64 | Same peak as C1, sixteen-fold dose |
| C3 | 51 °C | 15 s | 64 | Same dose as C2, higher peak |
| C4 | 51 °C | 60 s | 256 | Same peak as C3, four-fold dose |
| C5 | 53 °C | 15 s | 256 | Same dose as C4, higher peak |
Endpoints and timing. Perfusion by laser speckle or laser Doppler imaging of the exposed site before heating, immediately after, and at re-entry in subgroups at 24 and 72 hours. Vascular casting with radiopaque polymer and micro-computed tomography at days 3, 7, and 14 to measure vessel volume fraction as a function of radial distance. Immunohistochemistry for endothelial markers, including the combination that identifies the osteogenesis-coupled capillary subtype [31]. Osteocyte lacunar occupancy and apoptosis labeling by radial distance. Fluorochrome labels to time the onset of mineral apposition at the implant surface. Bone-to-implant contact and bone area fraction at 2 and 4 weeks.
Allocation and blinding. Sites are randomized to condition within animal with a balanced incomplete block design. Histomorphometry and image analysis are performed blind to condition.
Sample size. No estimate of the variance of radial vessel density after controlled heating was identified. A pilot will provide it. The main experiment is powered for the model-comparison analysis below, not for pairwise contrasts, and the number of animals is minimized by within-animal blocking in accordance with reduction principles.
Primary analysis. Mixed-effects regression of each outcome on (a) peak temperature, (b) log CEM43, and (c) Arrhenius-predicted survival from Stage B, with random effects for animal. Models are compared by cross-validated prediction error and information criteria. H1 is supported if the dose model outperforms the peak model by a prespecified margin. H2 is tested by the paired difference ρ_v−ρ_o estimated from radial profiles at day 3. The proportionality in equation (6) is examined by regressing the fluorochrome-derived onset time on w_d.
Confounding and bias
Mechanical damage from cutting and from implant insertion is the main confounder in any drilling experiment, because conditions that generate more heat also tend to generate more microdamage; drill speed has been associated with osteocyte apoptosis in a setting where thermal and mechanical contributions were both present [24]. Probe heating of a standardized osteotomy removes this confound in the main arm. Insertion torque is standardized and recorded. Animal-level variation in bone density is handled by blocking and by including density as a covariate. Site position along the bone is balanced across conditions.
Reproducibility and ethics
The finite element model, material parameters with sources, fitting code, and raw sensor data are to be deposited. The exact thermocouple positions as verified by imaging are reported, because sensor distance is the dominant uncontrolled variable in the existing literature. Animal work requires approval by an institutional animal care and use committee; humane endpoints, analgesia, and housing are specified in the protocol.
7. Analytical Development
Published thresholds are not iso-dose
Equation (2) can be applied to exposures reported in the literature. For a constant temperature T≥43 °C held for t minutes, CEM43=t⋅2^( T−43). Table 1 lists the result for conditions cited above.
| Exposure | CEM43 (min) | Reported observation | Source |
|---|---|---|---|
| 47 °C, 1 min | 16 | Threshold for heat-induced bone tissue injury on vital microscopy | [1] |
| 50 °C, 1 min | 128 | Consistent, widespread injury on vital microscopy; bone-to-implant contact reduced | [5, 6] |
| 55 °C, 1 min | 4,096 | Upper end of reported necrosis threshold range | [6] |
| 60 °C, 1 min | 131,072 | No significant impairment of osseointegration in dense bone; crestal bone loss and lower bone-to-implant contact in low-density bone | [7, 8] |
The conditions span four orders of magnitude in equivalent dose. If the CEM43 relation held for bone with R=0.5 and if all of these studies measured the same biological endpoint, they could not all be threshold conditions. Either the dose relation for bone is much flatter than in soft tissues (an R nearer to one), or the endpoints differ. The second reading is the more economical: vascular events at the low end, osteocyte necrosis in the middle, and failure of an implant to integrate only at the high end and only where the site cannot compensate. A single threshold cannot describe a system with at least three endpoints and a healing response that depends on the site.
Why duration and peak can diverge in practice
The depth to which heat penetrates in time t scales as ℓ∼√(4αt), with thermal diffusivity α=k/(ρc). Taking the measured conductivity of cortical bone, about 0.55 W/(m·K) [22], and assuming a volumetric heat capacity of 2.0–2.5 MJ/(m³·K), a range that must be confirmed from primary sources before use, gives α of roughly 2–3 × 10⁻⁷ m²/s. The penetration depth is then about 1 mm at 1 second and about 3 mm at 10 seconds. Two consequences follow. A brief, intense heating event at the cutting edge raises the temperature of a thin layer that the next drill is likely to remove. A prolonged, moderate event, such as a drill dwelling in dense bone under restricted irrigation, heats bone several millimeters away to a lower peak for a longer time, and that bone remains. The second event can register a lower peak at a nearby thermocouple and still deposit a larger retained dose. Guided surgery through a sleeve, deep osteotomies, and dense cortical sites are situations in which this pattern should be expected, and bench studies of guided and conventional protocols continue to be reported in terms of peak temperature [18].
Condition for a harmless hot step
If drill i produces vascular injury out to radius ρ_(v,i), the injury is entirely removed when
ρ_(v,i)≤r_n (7)
For the pilot drill the margin r_n−r_1 is typically the largest in the sequence, so a hot pilot step is the most forgiving. For the final drill the margin is zero, and any injury is retained. This yields a design rule that can be tested in Stage A: for a fixed total heat input, protocols that shift heat generation toward early steps should yield lower D_(ret) than protocols that shift it toward the final step. Single-drill protocols have no margin at any step.
Predictions that distinguish the models
The peak-temperature model predicts equal outcomes for C1 and C2, and for C3 and C4, in Table 2, and unequal outcomes for C2 and C3. The dose model predicts the reverse: C2 and C3 equal, C1 better than C2, C3 better than C4. A mixed result, in which both variables contribute, would indicate that the effective R for bone differs from 0.5, and the Stage B estimates would then be used to recompute dose. The two-compartment hypothesis predicts a range of conditions in which perfusion and vessel density are reduced while lacunar occupancy is preserved; its absence at every condition would refute H2.
8. Discussion
The proposal reinterprets a familiar threshold. The 47 °C criterion was the product of observing vessels, and its translation into a rule about necrosis measured at a thermocouple lost both the time dimension and the tissue compartment. Restoring them yields a model that is more complicated and makes sharper predictions.
Several alternative explanations for the inconsistent threshold literature should be weighed. Measurement geometry alone could account for much of it: a thermocouple 0.5 mm from the wall and one at 2 mm record very different peaks for the same event, and studies seldom verify sensor position. Species and site differences in cortical thickness and marrow content alter both heat transfer and healing. Endpoint timing matters, because necrotic bone is resorbed and replaced, and a late histomorphometric measurement may show recovery from an injury that was real. Mechanical damage is confounded with heat in every drilling study. The dose model does not exclude any of these; the probe-heating design is intended to control them so that the specific contribution of thermal history can be isolated.
The evidence that mild heat can stimulate osteogenic behavior [9] complicates any monotonic dose–response assumption. The response surface may have a region of benefit at low dose, a region of delayed healing through vascular injury at intermediate dose, and a region of tissue loss at high dose. A threshold framing obscures the first region entirely. Stage B is designed to detect non-monotonicity, and the in vivo design includes a low-dose condition for the same reason.
The two-compartment hypothesis could be wrong in a specific and informative way. Osteocytes are embedded in mineralized matrix with little convective cooling, whereas endothelial cells line vessels that carry heat away while flow persists; if anything, flow might protect vessels at low exposures. Against this, endothelial injury triggers stasis and thrombosis, which convert a sublethal cellular injury into loss of perfusion, an amplification that has no counterpart for osteocytes. Which effect dominates is an empirical matter.
There is also a question of practical value. If Stage A shows that peak temperature at a standardized sensor position is tightly correlated with retained dose across the protocols clinicians use, then peak temperature is an adequate surrogate and the main contribution of this work would be to standardize where it is measured. The framework would retain value for evaluating unconventional protocols, in which the correlation is most likely to break down: single-drill systems, low-speed drilling without irrigation, guided sleeves that restrict coolant, and thermal explantation, where heat is applied deliberately [6].
9. Clinical Significance
If retained dose proves to be the better predictor, three practical consequences follow. Drill systems and protocols would be evaluated by a dose map referenced to the final osteotomy wall, and manufacturers’ bench data would become comparable across laboratories. Surgical sequencing would acquire a rationale beyond incremental cutting load: the final drill should be the coolest and the briefest, and dwell time in dense bone during the last step should be minimized. And sites where early bone formation carries the burden of stability, such as low-density posterior maxilla and immediate-loading protocols, would be recognized as less tolerant of the same thermal history, which the low-density animal data already suggest [8].
The framework also bears on how thermal injury is recognized clinically. A devascularized annulus would not be visible at placement or on radiographs. Its signature would be slow early gain in stability and early marginal bone change, findings that are currently attributed to bone quality or loading. No diagnostic use is proposed here, and none should be inferred until the hypotheses are tested.
10. Limitations
The dose formalism is borrowed from hyperthermia, where exposures are longer and temperatures lower; its constants may not apply to seconds-long exposures above 50 °C, and the arithmetic in Table 1 inherits that uncertainty. Thermal properties of human jaw bone, especially cancellous bone with marrow, are incompletely characterized, and the heat capacity range used in Section 7.2 is an assumption. Cell-culture survival surfaces omit tissue-level phenomena such as thrombosis, which may dominate vascular injury in vivo. Probe heating differs from drilling in spatial profile and in the absence of cutting debris and microdamage, so the drilling arm is essential for transfer. Rabbits and minipigs differ from humans in remodeling rate and bone architecture. Perfusion imaging of bone is technically demanding and depth-limited, and vascular casting is terminal, so vascular endpoints are cross-sectional. The revascularization relation in equation (6) is a scaling argument with unmeasured parameters. The literature was assessed from abstracts and index records, and thermal thresholds attributed to older work were not checked against the full texts.
11. Future Validation
Beyond the three stages, independent replication of the discrimination experiment in a second species would test generality. A human observational study could relate retained dose, estimated from the calibrated model and recorded drilling parameters, to early stability trajectories measured by resonance frequency analysis [39]; this would require instrumented handpieces that log speed, torque, and time for each step. If the vascular hypothesis is supported, intraoperative assessment of site perfusion would become a research question in its own right. Finally, the parameters estimated for bone endothelium should be compared with those for other tissues compiled in the hyperthermia literature [12] to determine whether bone is unusual or whether the apparent inconsistency of thresholds was a matter of endpoint all along.
12. Conclusion
The peak-temperature threshold for osteotomy heating condenses a time-dependent, spatially distributed, multi-compartment process into one number. Published animal data are inconsistent with a single threshold and span several orders of magnitude when expressed as equivalent thermal dose. A model based on the dose retained beyond the final osteotomy wall, with separate sensitivities for vessels and osteocytes and an explicit link to the timing of bone formation, offers a coherent account and makes predictions that a peak-temperature criterion does not. Those predictions are untested. The proposed experiments are designed so that the model can be refuted, and the manuscript reports no data.
Cite this paper
Jain S, Gupta A. Beyond Peak Temperature: A Spatiotemporal Thermal-Dose Model Linking Implant Osteotomy Heating to Microvascular Injury and Early Osseointegration. Working paper. Center for Implant Dentistry; 2026. Available from: https://bayareaimplantdentistry.com/clinician-research-and-publications/osteotomy-vascular-injury
References
- Eriksson AR, Albrektsson T. Temperature threshold levels for heat-induced bone tissue injury: a vital-microscopic study in the rabbit. J Prosthet Dent. 1983;50(1):101-7. doi:10.1016/0022-3913(83)90174-9 (opens in a new tab). PMID: 6576145 (opens in a new tab).
- Tehemar SH. Factors affecting heat generation during implant site preparation: a review of biologic observations and future considerations. Int J Oral Maxillofac Implants. 1999;14(1):127-36. PMID: 10074763 (opens in a new tab).
- Augustin G, Davila S, Mihoci K, Udiljak T, Vedrina DS, Antabak A. Thermal osteonecrosis and bone drilling parameters revisited. Arch Orthop Trauma Surg. 2008;128(1):71-7. doi:10.1007/s00402-007-0427-3 (opens in a new tab). PMID: 17762937 (opens in a new tab).
- Möhlhenrich SC, Modabber A, Steiner T, Mitchell DA, Hölzle F. Heat generation and drill wear during dental implant site preparation: systematic review. Br J Oral Maxillofac Surg. 2015;53(8):679-89. doi:10.1016/j.bjoms.2015.05.004 (opens in a new tab). PMID: 26051868 (opens in a new tab).
- Eriksson RA, Albrektsson T, Magnusson B. Assessment of bone viability after heat trauma. A histological, histochemical and vital microscopic study in the rabbit. Scand J Plast Reconstr Surg. 1984;18(3):261-8. doi:10.3109/02844318409052849 (opens in a new tab). PMID: 6549359 (opens in a new tab).
- Kniha K, Heussen N, Weber E, Möhlhenrich SC, Hölzle F, Modabber A. Temperature Threshold Values of Bone Necrosis for Thermo-Explantation of Dental Implants-A Systematic Review on Preclinical In Vivo Research. Materials (Basel). 2020;13(16). doi:10.3390/ma13163461 (opens in a new tab). PMID: 32781597 (opens in a new tab).
- Trisi P, Berardini M, Falco A, Vulpiani MP, Masciotra L. Effect of 50 to 60°C heating on osseointegration of dental implants in dense bone: an in vivo histological study. Implant Dent. 2014;23(5):516-21. doi:10.1097/ID.0000000000000162 (opens in a new tab). PMID: 25238268 (opens in a new tab).
- Trisi P, Berardini M, Falco A, Vulpiani MP. Effect of temperature on the dental implant osseointegration development in low-density bone: an in vivo histological evaluation. Implant Dent. 2015;24(1):96-100. doi:10.1097/ID.0000000000000204 (opens in a new tab). PMID: 25621555 (opens in a new tab).
- Dolan EB, Haugh MG, Tallon D, Casey C, McNamara LM. Heat-shock-induced cellular responses to temperature elevations occurring during orthopaedic cutting. J R Soc Interface. 2012;9(77):3503-13. doi:10.1098/rsif.2012.0520 (opens in a new tab). PMID: 22915633 (opens in a new tab).
- Sapareto SA, Dewey WC. Thermal dose determination in cancer therapy. Int J Radiat Oncol Biol Phys. 1984;10(6):787-800. doi:10.1016/0360-3016(84)90379-1 (opens in a new tab). PMID: 6547421 (opens in a new tab).
- Dewhirst MW, Viglianti BL, Lora-Michiels M, Hanson M, Hoopes PJ. Basic principles of thermal dosimetry and thermal thresholds for tissue damage from hyperthermia. Int J Hyperthermia. 2003;19(3):267-94. doi:10.1080/0265673031000119006 (opens in a new tab). PMID: 12745972 (opens in a new tab).
- Yarmolenko PS, Moon EJ, Landon C, Manzoor A, Hochman DW, Viglianti BL, et al. Thresholds for thermal damage to normal tissues: an update. Int J Hyperthermia. 2011;27(4):320-43. doi:10.3109/02656736.2010.534527 (opens in a new tab). PMID: 21591897 (opens in a new tab).
- Eriksson AR, Albrektsson T, Albrektsson B. Heat caused by drilling cortical bone. Temperature measured in vivo in patients and animals. Acta Orthop Scand. 1984;55(6):629-31. doi:10.3109/17453678408992410 (opens in a new tab). PMID: 6524329 (opens in a new tab).
- Eriksson RA, Adell R. Temperatures during drilling for the placement of implants using the osseointegration technique. J Oral Maxillofac Surg. 1986;44(1):4-7. doi:10.1016/0278-2391(86)90006-6 (opens in a new tab). PMID: 3455722 (opens in a new tab).
- Lundskog J. Heat and bone tissue. An experimental investigation of the thermal properties of bone and threshold levels for thermal injury. Scand J Plast Reconstr Surg. 1972;9:1-80. PMID: 4661159 (opens in a new tab).
- Kosior P, Kiryk S, Kotela A, Kiryk J, Kensy J, Laszczyńska M, et al. Histological and Histomorphometric Insights into Implant Bed Preparation: A Systematic Review. J Clin Med. 2025;14(13). doi:10.3390/jcm14134538 (opens in a new tab). PMID: 40648910 (opens in a new tab).
- Feldmann A, Wandel J, Zysset P. Reducing temperature elevation of robotic bone drilling. Med Eng Phys. 2016;38(12):1495-1504. doi:10.1016/j.medengphy.2016.10.001 (opens in a new tab). PMID: 27789226 (opens in a new tab).
- Gedik B, Keskin Yalcin B, Etik E, Cankaya AB, Erdem MA. Comparative evaluation of intraosseous temperature and drilling time using four different drill designs in implant site preparation. BMC Oral Health. 2025;25(1):1453. doi:10.1186/s12903-025-06860-z (opens in a new tab). PMID: 41013457 (opens in a new tab).
- Lee J, Rabin Y, Ozdoganlar OB. A new thermal model for bone drilling with applications to orthopaedic surgery. Med Eng Phys. 2011;33(10):1234-44. doi:10.1016/j.medengphy.2011.05.014 (opens in a new tab). PMID: 21803638 (opens in a new tab).
- Chen YC, Tsai YJ, Hsiao HY, Chiu YW, Hong YY, Tu YK, et al. Assessment of Thermal Osteonecrosis during Bone Drilling Using a Three-Dimensional Finite Element Model. Bioengineering (Basel). 2024;11(6). doi:10.3390/bioengineering11060592 (opens in a new tab). PMID: 38927828 (opens in a new tab).
- Aydın K, Ökten K, Uğur L. An analytical and numerical approach to the determination of thermal necrosis in cortical bone drilling. Int J Numer Method Biomed Eng. 2022;38(10):e3640. doi:10.1002/cnm.3640 (opens in a new tab). PMID: 35899364 (opens in a new tab).
- Davidson SR, James DF. Measurement of thermal conductivity of bovine cortical bone. Med Eng Phys. 2000;22(10):741-7. doi:10.1016/s1350-4533(01)00003-0 (opens in a new tab). PMID: 11334760 (opens in a new tab).
- Aghvami M, Brunski JB, Serdar Tulu U, Chen CH, Helms JA. A Thermal and Biological Analysis of Bone Drilling. J Biomech Eng. 2018;140(10):1010101-8. doi:10.1115/1.4040312 (opens in a new tab). PMID: 30029243 (opens in a new tab).
- Wang L, Aghvami M, Brunski J, Helms J. Biophysical regulation of osteotomy healing: An animal study. Clin Implant Dent Relat Res. 2017;19(4):590-599. doi:10.1111/cid.12499 (opens in a new tab). PMID: 28608504 (opens in a new tab).
- Kniha K, Hermanns-Sachweh B, Al-Sibai F, Kneer R, Möhlhenrich SC, Heitzer M, et al. Effect of thermal osteonecrosis around implants in the rat tibia: numerical and histomorphometric results in context of implant removal. Sci Rep. 2022;12(1):22227. doi:10.1038/s41598-022-25581-9 (opens in a new tab). PMID: 36564495 (opens in a new tab).
- HENRIQUES FC Jr. Studies of thermal injury; the predictability and the significance of thermally induced rate processes leading to irreversible epidermal injury. Arch Pathol (Chic). 1947;43(5):489-502. PMID: 20243514 (opens in a new tab).
- Dolan EB, Haugh MG, Voisin MC, Tallon D, McNamara LM. Thermally induced osteocyte damage initiates a remodelling signaling cascade. PLoS One. 2015;10(3):e0119652. doi:10.1371/journal.pone.0119652 (opens in a new tab). PMID: 25785846 (opens in a new tab).
- Berglundh T, Abrahamsson I, Lang NP, Lindhe J. De novo alveolar bone formation adjacent to endosseous implants. Clin Oral Implants Res. 2003;14(3):251-62. doi:10.1034/j.1600-0501.2003.00972.x (opens in a new tab). PMID: 12755774 (opens in a new tab).
- Davies JE. Understanding peri-implant endosseous healing. J Dent Educ. 2003;67(8):932-49. PMID: 12959168 (opens in a new tab).
- Terheyden H, Lang NP, Bierbaum S, Stadlinger B. Osseointegration–communication of cells. Clin Oral Implants Res. 2012;23(10):1127-35. doi:10.1111/j.1600-0501.2011.02327.x (opens in a new tab). PMID: 22092345 (opens in a new tab).
- Kusumbe AP, Ramasamy SK, Adams RH. Coupling of angiogenesis and osteogenesis by a specific vessel subtype in bone. Nature. 2014;507(7492):323-328. doi:10.1038/nature13145 (opens in a new tab). PMID: 24646994 (opens in a new tab).
- Ramasamy SK, Kusumbe AP, Wang L, Adams RH. Endothelial Notch activity promotes angiogenesis and osteogenesis in bone. Nature. 2014;507(7492):376-380. doi:10.1038/nature13146 (opens in a new tab). PMID: 24647000 (opens in a new tab).
- Stegen S, van Gastel N, Carmeliet G. Bringing new life to damaged bone: the importance of angiogenesis in bone repair and regeneration. Bone. 2015;70:19-27. doi:10.1016/j.bone.2014.09.017 (opens in a new tab). PMID: 25263520 (opens in a new tab).
- McCarthy I. The physiology of bone blood flow: a review. J Bone Joint Surg Am. 2006;88 Suppl 3:4-9. doi:10.2106/JBJS.F.00890 (opens in a new tab). PMID: 17079361 (opens in a new tab).
- PENNES HH. Analysis of tissue and arterial blood temperatures in the resting human forearm. J Appl Physiol. 1948;1(2):93-122. doi:10.1152/jappl.1948.1.2.93 (opens in a new tab). PMID: 18887578 (opens in a new tab).
- Roache PJ. Perspective: A Method for Uniform Reporting of Grid Refinement Studies. Journal of Fluids Engineering. 1994;116(3):405-413. doi:10.1115/1.2910291 (opens in a new tab).
- American Society of Mechanical Engineers. Assessing credibility of computational modeling through verification and validation: application to medical devices. ASME V&V 40-2018. New York: ASME; 2018.
- Percie du Sert N, Hurst V, Ahluwalia A, Alam S, Avey MT, Baker M, et al. The ARRIVE guidelines 2.0: Updated guidelines for reporting animal research. PLoS Biol. 2020;18(7):e3000410. doi:10.1371/journal.pbio.3000410 (opens in a new tab). PMID: 32663219 (opens in a new tab).
- Sennerby L, Meredith N. Implant stability measurements using resonance frequency analysis: biological and biomechanical aspects and clinical implications. Periodontol 2000. 2008;47:51-66. doi:10.1111/j.1600-0757.2008.00267.x (opens in a new tab). PMID: 18412573 (opens in a new tab).

