Skip to main content

Where Does the Error Come From? An Error-Propagation Model for Robot-Assisted Dental Implant Placement and a Coordinate-Measured Phantom Protocol to Apportion Deviation Among Imaging, Registration, Tracking, Actuation, and Tool-Bone Interaction

Paper type
Technical methodology article with analytic error model, prospective phantom-study protocol, and invention disclosure appendix (no original experimental data)
Status
Original Work · Working Paper
Keywords:
robotic implant surgery · computer-assisted implant surgery · accuracy · target registration error · error propagation · optical tracking · uncertainty budget · phantom validation
Contents
  1. 1Introduction and Clinical Significance
  2. 2Critical Review of the Established Literature
  3. 3Identification of the Specific Research Gap
  4. 4Scientific Objective and Hypothesis
  5. 5Theoretical Foundation: Error Propagation
  6. 6Methodology
  7. 7Evidence Synthesis and Explicitly Labeled Theoretical Predictions
  8. 8Discussion: Mechanisms and Competing Explanations
  9. 9Implications for Implant Surgery and Restorative Dentistry
  10. 10Technical and Clinical Limitations
  11. 11Proposed Experimental and Clinical Validation
  12. 12Future Research Directions
  13. 13Evidence-Calibrated Conclusion

Abstract

Background: Meta-analyses of clinical studies report mean deviations for robot-assisted implant placement of approximately 0.6 to 0.7 mm at the platform and apex and 1.6 degrees in angle, lower than pooled values for static guides and dynamic navigation. Heterogeneity is extreme, tracking modality is a significant moderator, and no trial has shown that the gain in accuracy improves a patient-relevant outcome. Reported deviations aggregate every error from image acquisition to postoperative measurement and do not reveal their origin.

Objective: To formalize how errors propagate through a robotic implant workflow, to interpret published accuracy figures in that light, and to specify an experiment that apportions deviation among sources.

Methods: Critical review of systematic reviews and meta-analyses of computer-assisted implant surgery and of the registration-error literature in image-guided surgery. An error model was derived in which platform and angular errors combine to give apex error and in which source variances add. A phantom protocol was designed with independent reference measurement and deliberate injection of known errors at each stage in a fractional factorial layout.

Findings: Under small-angle geometry, mean-square apex deviation equals mean-square platform deviation plus the product of squared implant length and mean-square angular deviation. With the pooled clinical values, the angular term contributes a minority of apex deviation for a 10 mm implant and becomes comparable to the platform term only for long implants or angular errors of several degrees. Because platform error is itself largely the product of registration and tracking, we hypothesize that the navigation chain, and not robot actuation, accounts for at least half of apex variance. A contribution of 50 percent or more from actuation and tool-bone interaction combined would refute the hypothesis.

Conclusions: Robotic placement is the most accurate form of guided implant surgery in pooled comparisons, on a surrogate endpoint. Improving it further requires knowing which link dominates, which accuracy studies as currently designed cannot show. The model's numerical illustrations use published means and assumed values and are not experimental results.

Keywords: robotic implant surgery; computer-assisted implant surgery; accuracy; target registration error; error propagation; optical tracking; uncertainty budget; phantom validation

1. Introduction and Clinical Significance

Computer-assisted implant surgery transfers a virtual plan to the patient by one of three means. Static guides constrain the drill mechanically through a sleeve in a template. Dynamic navigation tracks the handpiece and the patient and displays their relation to the plan while the surgeon drills freehand. Robotic systems add an actuated arm that positions and holds, or advances, the handpiece along the planned trajectory, either under haptic constraint with the surgeon's hand on the instrument or autonomously under supervision [1, 2]. The first robotic system for dental implant surgery received marketing clearance in the United States through the premarket notification pathway as a Class II device [3], and several systems are now in clinical use internationally.

The case for a robot rests on accuracy. A planned implant position encodes clearances from the inferior alveolar canal, adjacent roots, and sinus, and a prosthetically driven emergence within a tolerance that, in the anterior maxilla, is commonly described in terms of zones a millimeter or two wide [4]. Safety margins of 2 mm from vital structures are conventionally recommended in guided surgery because static guides deviate by more than a millimeter on average, with outliers of several millimeters [5]. If a robot reduced both the mean and the spread of deviation, margins could be narrowed and plans made more demanding.

Accuracy is nonetheless a surrogate. A critical review asking whether computer-assisted implant surgery improves clinical outcomes or reduces complications concluded that evidence for patient-level benefit was limited [6]. The framework for evaluating surgical innovation holds that a new technique should progress from proof of concept through development and exploration to assessment against established alternatives on outcomes that matter [7]. Robotic implant surgery is at the exploration stage: its technical performance has been characterized in many small studies, and its clinical consequence has not.

This paper addresses the technical question that precedes the clinical one. A deviation measured after surgery is the end product of a sequence of imperfect steps. Knowing the total does not tell an engineer what to improve or a surgeon what to check. We set out a model of how the errors combine, reinterpret published accuracy data with it, and design an experiment to separate the sources.

2. Critical Review of the Established Literature

Accuracy of static and dynamic guidance

A systematic review and meta-analysis of static computer-aided implant surgery, prepared for a consensus conference, reported mean deviations of roughly 1.2 mm at the entry point, 1.4 mm at the apex, and 3.5 degrees in angle, with accuracy better in partially than in fully edentulous cases [5]; earlier reviews had found similar means with maximum deviations of several millimeters [8–10]. An analysis of how template positioning error affects implants placed through a mucosa-supported guide showed that seating of the guide is a major and variable contributor [11]. For dynamic navigation, meta-analyses report mean deviations of about 1 mm at the platform, somewhat more at the apex, and between 3 and 4 degrees [12, 13], and a clinical series found accuracy similar to that of static guides and better than freehand placement [14].

Accuracy of robotic guidance

A systematic review and meta-analysis of robot-assisted implant surgery found pooled clinical deviations of 0.6 mm at the platform, 0.7 mm at the apex, and 1.6 degrees, and, in vitro, significantly smaller apical and angular deviations with robotic than with other computer-assisted placement [15]. A second meta-analysis restricted to clinical studies reported platform, apex, and angular deviations of 0.69 mm, 0.72 mm, and 1.62 degrees, each with heterogeneity statistics above 90 percent, and identified tracking modality as a significant moderator [16]. A network comparison of static, dynamic, and robotic guidance across 67 articles found the lowest deviations for robotic placement [17]. Individual clinical reports show how much results differ between settings: a series using haptic robotic guidance in completely edentulous arches reported mean deviations of about 1.0 mm at the platform, 0.95 mm at the apex, and 2.6 degrees [18], whereas a prospective single-arm trial in partially edentulous patients reported 0.53 mm at both platform and apex with a mean angular deviation of 2.8 degrees [19]; other reports describe operating procedures and accuracy for particular systems [20].

Four features of this evidence limit inference. First, heterogeneity of the magnitude reported means that the pooled value describes no particular system or setting. Second, most studies are small, single-arm, and conducted by developers or early adopters. Third, the comparators in indirect comparisons were studied in different eras, with different imaging and measurement methods. Fourth, and least discussed, the outcome is measured by superimposing a postoperative scan on the plan, a registration that has its own error, so that every reported deviation is the sum of a placement error and an evaluation error.

Registration and tracking error in image-guided surgery

The theory of error in point-based rigid registration was developed for neurosurgical and otologic navigation and applies directly. Fitzpatrick and colleagues distinguished fiducial localization error, the error in locating each fiducial; fiducial registration error, the residual misfit after registration, which is what systems display; and target registration error, the error at the point of surgical interest, which is what matters and is not directly observable [21]. They derived an expression for expected target registration error as a function of fiducial localization error, the number and configuration of fiducials, and the position of the target relative to them, and later its distribution [22]. Two consequences are counterintuitive and clinically important: a small displayed registration residual does not imply a small error at the target, and error grows with the distance of the target from the centroid of the fiducials, most steeply along directions in which the fiducial array is narrow. The same analysis governs optically tracked instruments, whose tip error depends on marker geometry and on the distance from the marker array to the tip [23]. Reviews of error in image-guided craniomaxillofacial surgery catalog the practical sources: imaging resolution and distortion, fiducial displacement, registration, tracking, tool calibration, and tissue or patient movement [24].

Imaging and data fusion

Cone-beam computed tomography supplies the bone geometry. Its limitations include finite voxel size, beam-hardening and scatter artifacts from metallic restorations, patient motion, and gray values that are not calibrated density units [25, 26]. Prosthetically driven planning requires merging the tomographic volume with an optical surface scan of the dentition; that registration is a prerequisite for guided surgery and a recognized source of error, particularly where few teeth remain or metal artifacts degrade the tomographic surface [27]. Errors introduced here are common to static, dynamic, and robotic workflows.

What robots add and what they cannot remove

A robot arm with encoders and brakes removes the surgeon's hand tremor and drift from the last link of the chain. It does not remove errors that occur upstream: the robot faithfully executes a trajectory defined in a coordinate frame that is tied to the patient through registration and tracking. Nor does it fully remove errors at the tool-bone interface. A drill entering a sloped or dense cortical surface is deflected laterally, the handpiece and drill have compliance and runout, and the patient's jaw moves under drilling force unless tracking compensates with sufficient bandwidth. Mechanical tracking through a jointed arm fixed to a splint and optical tracking with cameras and reflective markers differ in line-of-sight requirements, in sensitivity to splint seating, and in latency, which may explain why tracking modality emerged as a moderator in pooled analysis [16].

3. Identification of the Specific Research Gap

Established: pooled clinical deviations for robotic placement are below those for static and dynamic guidance; heterogeneity is very large; tracking modality matters. Uncertain: what the deviations of a given system are in a given clinical situation, how much of each reported deviation is evaluation error, and which stage of the workflow is the principal source.

Current accuracy studies are inadequate to answer these because of their design. They measure one end-to-end quantity. They use the same imaging modality for planning and for evaluation, so that systematic imaging errors cancel or compound unpredictably. They report means and standard deviations of unsigned three-dimensional distances, which are not normally distributed and whose means depend on both bias and spread. They rarely report the uncertainty of the evaluation method. They test under favorable conditions, with dentate phantoms, good access, and homogeneous materials, so that the tails of the distribution, the outliers that injure nerves, are unexplored. Clinical studies cannot manipulate error sources at all.

The specific gap is an error budget: a decomposition of total placement variance into contributions from identifiable sources, obtained by an experiment in which each source can be perturbed independently and the result is measured by a reference method substantially more accurate than the system under test.

4. Scientific Objective and Hypothesis

The objective is to apportion the deviation of robot-assisted implant placement among imaging and data fusion, patient registration, tracking, robot actuation, and tool-bone interaction.

Hypothesis H9: for implants 10 mm or longer placed with a contemporary robotic system under conditions representative of clinical use, registration and tracking together (the navigation chain) account for at least 50 percent of the variance in three-dimensional apex deviation, and robot actuation and tool-bone interaction together account for less than 50 percent.

H9 is falsified if, in the factorial error-injection experiment described below, with deviation measured by an independent coordinate reference, the estimated variance contribution of actuation and tool-bone interaction combined is 50 percent or more, with a confidence interval excluding lower values. A corollary, H9b, concerns geometry: the excess of mean-square apex deviation over mean-square platform deviation equals the product of squared implant length and mean-square angular deviation within measurement uncertainty. H9b is falsified if the observed excess departs from that product by more than the combined uncertainty, which would indicate curvature of the osteotomy path, depth error, or correlation between platform and angular error that the model omits.

The hypothesis is about relative contribution and makes no claim that robots are inaccurate. If it holds, the route to better accuracy lies in fiducial design, registration verification, and tracking, and gains from stiffer or more precise arms will be small. If it fails, the arm and the tool-bone interface deserve the engineering attention.

5. Theoretical Foundation: Error Propagation

Deviation measures

Let the planned implant axis be defined by a platform point and a unit direction, and the achieved axis likewise. The platform deviation Δp is the distance between planned and achieved platform points; the angular deviation θ is the angle between the two directions; the apex deviation Δa is the distance between planned and achieved apex points for an implant of length L. Depth deviation is the component of platform deviation along the planned axis. From the geometry of two lines,

Δ_a ≤ Δ_p + L θ (1)

with θ in radians, since the apex is displaced from where a parallel shift alone would put it by at most the arc swept over length L.

Combination of platform and angular error

If platform error and angular error are uncorrelated and angles are small, the lateral apex error is the vector sum of the lateral platform error and an independent term of magnitude Lθ in a random direction, so that mean-square values add:

E(Δ_a^2) = E(Δ_p^2) + L^2 E(θ^2) (2)

The share of mean-square apex deviation attributable to angular error is then

A = (L^2 E(θ^2))/(E(Δ_p^2) + L^2 E(θ^2)) (3)

This relation allows published summary values to be checked for internal consistency. Taking the pooled clinical means of 0.6 mm for platform deviation and 1.6 degrees (0.028 radian) for angular deviation [15] as rough stand-ins for root-mean-square values, a 10 mm implant gives an angular term of 0.28 mm and a predicted apex value of about 0.66 mm, close to the reported 0.7 mm, with A near 0.18. The substitution of means for root-mean-square values is an approximation, and the calculation is an illustration of the relation, not an estimate of any system's performance. Its message is that at the angular accuracy reported for robotic placement, apex deviation for implants of ordinary length is dominated by platform deviation. The angular term equals the platform term only when Lθ equals Δp, which for 0.6 mm and 1.6 degrees requires a length of about 21 mm, the range of zygomatic and not of conventional implants. For static guidance, with angular deviations near 3.5 degrees [5], the angular term for a 13 mm implant is about 0.8 mm and is comparable to the platform term, which is why apex deviations exceed platform deviations more noticeably in that literature.

Source decomposition

Placement error at any point is the sum of contributions from stages that are, to a first approximation, independent. Variances therefore add:

σ_place^2 = σ_img^2 + σ_reg^2 + σ_trk^2 + σ_rob^2 + σ_tool^2 (4)

where the subscripts denote imaging and data fusion, patient registration, tracking, robot actuation and calibration, and tool-bone interaction including drill deflection, runout, and patient motion not compensated by tracking. What an accuracy study reports is

σ_obs^2 = σ_place^2 + σ_eval^2 (5)

where σeval is the error of the evaluation method, principally the registration of the postoperative scan to the plan and the localization of the implant axis in an image degraded by metal artifact. Equation 5 has a practical consequence: as placement becomes more accurate, evaluation error becomes a larger fraction of what is observed, and differences between accurate systems may reflect differences in how they were measured. A reference measurement with σeval several times smaller than σplace is needed to see the latter clearly; conventional metrological practice asks for a ratio of at least four.

Target registration error

For point-based rigid registration with N fiducials, each localized with independent isotropic error of mean square FLE2, the expected squared target registration error at a target position r is approximately

E(TRE^2) = (FLE^2)/N (1 + 1/3 ∑_k=1^3 (d_k^2)/(f_k^2)) (6)

where dk is the distance of the target from principal axis k of the fiducial configuration and fk is the root-mean-square distance of the fiducials from that axis [21]. The expression makes three design statements. Error at the fiducial centroid is the localization error reduced by the square root of N. Error increases quadratically as the target moves away from the centroid. And the increase is steepest about axes around which the fiducials are tightly clustered, that is, a compact fiducial array resists rotation poorly. A fiducial splint clipped to three adjacent teeth has small fk; an implant site at the opposite end of the arch has large dk. The model therefore predicts that robotic accuracy degrades with distance from the splint and is worst in distal extension and fully edentulous cases, where fiducials must be bone-anchored. Surface-based registration to teeth follows the same logic with the registered surface patch in place of discrete fiducials.

Tracking

An optically tracked rigid body with marker spacing b and per-marker localization error σm has an orientation uncertainty of the order of

σ_φ ≈ (√(2) σ_m)/b (7)

in radians, and a point at distance D from the marker array inherits a position uncertainty of approximately Dσφ in addition to the translational uncertainty of the array [23]. As an illustration with assumed values, σm of 0.1 mm and b of 50 mm give 0.0028 radian (0.16 degree), and a drill tip 80 mm from the array acquires about 0.23 mm from this term alone. Mechanical tracking through a linkage replaces this term with the accumulated encoder and joint-compliance error of the linkage and adds sensitivity to the seating and stiffness of the patient attachment. In both cases the patient-side reference contributes as much as the tool-side.

Tool-bone interaction

A drill of free length ℓ and bending stiffness EI, loaded laterally at its tip by a force Flat arising from an inclined or inhomogeneous cortical surface, deflects by approximately

δ = (F_(lat) ℓ^3)/(3 E I) (8)

treating it as a cantilever. The cubic dependence on free length means that long drills through a guide-free approach are disproportionately susceptible. A stiff robot holding the handpiece does not prevent deflection of the drill itself or compliance at the handpiece chuck. This term is expected to be small in homogeneous phantoms and larger in sloped ridges, extraction sockets, and dense cortical bone, conditions under which few robotic accuracy studies have been conducted.

6. Methodology

Review methods

The review is narrative. Pooled accuracy values are those of the cited meta-analyses; no new pooling was performed. Regulatory and patent information was taken from public records of the issuing agencies as identified during the research phase and is cited as such.

Phantom design

The phantom is a set of anatomically shaped jaw models with radiodensity and drilling characteristics approximating cortical and cancellous bone, mounted on a kinematic base that locates each model repeatably on the table of a coordinate measuring machine. Each model carries reference spheres whose centers are certified by the coordinate measuring machine and are visible in tomography; these define a model coordinate frame independent of the robot, the tracker, and the imaging system. Models represent four scenarios: single posterior site in a dentate arch; distal extension; fully edentulous arch; and an anterior extraction socket with a sloped palatal wall. Planned implant sites are distributed at graded distances from the fiducial splint position.

Reference measurement

After each osteotomy and implant placement, a precision cylindrical gauge pin matched to the implant connection is seated, and its axis and a datum point at the platform are measured by the coordinate measuring machine in the model frame. The planned position is known in the same frame through the reference spheres. Deviations are thus obtained without postoperative imaging and without image registration. The expanded uncertainty of this reference chain is established before the study by repeated measurement and reported according to the guide to the expression of uncertainty in measurement [28]; the target is an expanded uncertainty below 0.05 mm and 0.1 degree. For comparison with the literature, each site is also evaluated by the conventional method, postoperative tomography superimposed on the plan, so that σeval of that method can be estimated directly from Equation 5 as the difference between the two.

Error injection

Each source in Equation 4 is perturbed at two levels, nominal and deliberately degraded by a known amount, in a fractional factorial design (Table 1). Because the injected perturbations are known, the sensitivity of platform, apex, and angular deviation to each source is estimated directly, and the nominal contribution of each source follows from the sensitivity and from an independent estimate of that source's nominal variance obtained in dedicated sub-experiments (repeat registrations without drilling; tracking of a static tool; robot positioning to a target in air measured by the coordinate measuring machine; drilling with the robot locked and the model rigidly fixed).

Table 1. Error sources, nominal conditions, and injected perturbations in the phantom protocol.
SourceNominal conditionInjected perturbation
Imaging and data fusionManufacturer-recommended tomographic protocol; surface-scan merge on intact dentitionLarger voxel size; metal restorations adjacent to the merge region; reduced dentition for merging
Patient registrationFiducial splint seated and verified per instructionsSplint seated with a shim of known thickness on one abutment tooth; reduced number of supporting teeth
TrackingRecommended tracker geometry and line of sightIncreased tracker-to-marker distance or oblique viewing angle; for mechanical tracking, compliant splint attachment
Robot actuationCalibrated arm, recommended workspaceOperation near workspace limit; payload offset; calibration deliberately offset by a known amount
Tool-bone interactionFlat crest, homogeneous analog, standard drill lengthSloped cortical entry; dense cortical layer; extended drill length; unconstrained model allowing motion under load
Implant length10 mm13 mm and 16 mm (to test Equation 2)

Outcomes and analysis

Primary outcomes are signed deviations in the model frame: platform deviation resolved into mesiodistal, buccolingual, and depth components; angular deviation resolved into two orthogonal tilt components; and apex deviation likewise. Signed components allow bias (mean) to be separated from precision (standard deviation), in the sense of trueness and precision defined for measurement methods [29]; unsigned three-dimensional distances are reported in addition for comparability. Variance components are estimated in a linear mixed model with the injected factors as fixed effects and model, site, and session as random effects. The variance share of the navigation chain is the sum of the registration and tracking contributions divided by total placement variance at nominal settings, with a bootstrap confidence interval. H9b is examined by regressing the excess of squared apex over squared platform deviation on squared implant length times squared angular deviation.

Sample size and replication

Variance components require many observations. A design with 16 runs of the fractional factorial, each comprising 12 implant sites across the four scenarios, replicated three times, yields 576 placements. Precision of a variance estimate from n observations is roughly proportional to the square root of 2/n, so that each main contribution is estimated with a relative standard error of the order of 10 percent; the final number should be fixed after a pilot establishes the nominal variances. Operators follow the manufacturer's instructions for use and are trained to the manufacturer's standard. At least two robotic systems with different tracking principles are tested where access can be obtained, since the hypothesis may hold for one and fail for another.

7. Evidence Synthesis and Explicitly Labeled Theoretical Predictions

Synthesis of published accuracy

Table 2 collects the pooled values quoted in Section 2. They should be read with their limitations: unsigned means, heterogeneous methods, and unquantified evaluation error.

Table 2. Pooled deviations for guided implant placement as reported in the cited meta-analyses. Values are rounded; consult the sources for confidence intervals and inclusion criteria.
GuidancePlatform (mm)Apex (mm)Angle (degrees)Source
Static guidesabout 1.2about 1.4about 3.5[5]
Dynamic navigationabout 1.0about 1.3about 3.6[12]
Robotic, clinical0.60.71.6[15]
Robotic, clinical0.690.721.62[16]

Theoretical predictions

The following are predictions of the model in Section 5. They have not been tested.

Prediction 1. Placement deviation will increase with distance of the implant site from the fiducial splint, in proportion to the rotational term of Equation 6, and the increase will be larger in the direction perpendicular to the long axis of the splint.

Prediction 2. The registration perturbation (a shim under the splint) will produce the largest change in apex deviation per unit of injected error of any source, because it rotates the entire planned frame.

Prediction 3. In homogeneous phantoms with flat entry, the tool-bone contribution will be small; with a sloped dense cortical entry it will become a major contributor to platform deviation in the downslope direction, and that deviation will appear as bias, not random scatter.

Prediction 4. The conventional evaluation method will overstate deviation relative to the coordinate reference by an amount corresponding to an evaluation standard deviation of a few tenths of a millimeter, a substantial fraction of the deviations reported for robotic systems.

Prediction 5. The excess of apex over platform mean-square deviation will scale with the square of implant length as in Equation 2.

Prediction 6. Under H9, replacing the robot arm with an ideal positioner in simulation would reduce apex variance by less than half.

8. Discussion: Mechanisms and Competing Explanations

The hypothesis that the navigation chain dominates is supported by indirect reasoning: the robot's own repeatability, for industrial-grade arms, is typically far smaller than the deviations reported clinically; the same registration and tracking technologies in dynamic navigation yield millimeter-level errors; and tracking modality moderates robotic accuracy [16]. It is not established, and several considerations argue against it.

The most direct counter-argument is the comparison between dynamic navigation and robotics itself. Both rely on registration and tracking. If those dominated, the two should perform alike, yet pooled robotic deviations are roughly half those of dynamic navigation in both position and angle (Table 2). The difference must come from the last link: the robot holds a trajectory that a surgeon's hand cannot. That shows the human hand to be a large error source in dynamic navigation; it does not show that, once the hand is replaced, the arm is the largest remaining source. What remains after the hand is removed is exactly what H9 is about, and the factorial experiment addresses it. The comparison is also confounded by era and by measurement method, and registration procedures differ between systems.

A second counter-argument concerns tool-bone interaction. Clinical drilling encounters conditions, an oblique socket wall, a knife-edge ridge, type I cortical bone, that deflect drills by amounts comparable to the total deviations reported. If accuracy studies have been conducted mostly on favorable sites and phantoms, tool-bone error has been systematically under-sampled, and in demanding sites it could exceed the navigation contribution. The scenario stratification in the protocol is designed to expose this. A result in which H9 holds on flat homogeneous sites and fails on sloped dense ones would be informative and plausible.

A third consideration is correlation. The additive variance model assumes independent sources. Patient motion violates this: movement of the jaw under drilling force is an interaction between tool-bone load, splint compliance, and tracking latency. If such interactions are large, a main-effects decomposition will leave substantial unexplained variance, which would itself be a finding and would direct attention to dynamic compensation.

The treatment of evaluation error deserves emphasis because it affects the entire literature. Postoperative tomography locates a titanium cylinder surrounded by beam-hardening artifact and registers it to the plan through bone or tooth surfaces. Reproducibility studies of this procedure are few. If its standard deviation is 0.2 to 0.3 mm, a possibility the protocol will test, then a reported platform deviation of 0.6 mm contains a meaningful evaluation component, and the true differences between robotic systems, or between robotic and the best static guides in dentate cases, are known less precisely than confidence intervals on pooled means suggest. Meta-analytic heterogeneity above 90 percent is what one would expect if studies differ in evaluation method as much as in placement accuracy.

The use of unsigned distances is a related problem. The mean of an unsigned three-dimensional deviation is always positive and depends on both systematic offset and scatter. Two systems with the same mean may differ entirely in character: one biased and precise, correctable by calibration, the other unbiased and imprecise, not correctable. Clinical risk depends on the tail of the distribution in the direction of a vital structure, which is governed by signed bias and directional spread. Reporting signed components in an anatomical frame would make accuracy data usable for setting safety margins.

Finally, whether any of this matters to patients is open. Mean deviations of well under a millimeter are already within the tolerances of most restorative plans. The clinical value of robotic placement may lie less in mean accuracy than in the suppression of gross outliers, in consistency across operators, or in enabling flapless and immediate protocols, each of which requires its own evidence. The absence of outcome trials [6] is the principal limitation of the field, and an error budget does not substitute for them.

9. Implications for Implant Surgery and Restorative Dentistry

For surgeons using robotic or dynamic systems, the theory of target registration error has immediate practical content that does not depend on the proposed experiment. A low registration residual displayed by the system is not assurance of accuracy at the implant site [21]. Accuracy should be verified at or near the surgical site before drilling, by touching identifiable landmarks and confirming their displayed position. Fiducial splints should be seated on as many stable teeth as possible, as close to the surgical site as access allows, and their seating rechecked during the procedure. Sites remote from the fiducials, and edentulous cases with bone-anchored fiducials, warrant larger safety margins. Data fusion between tomography and surface scan should be inspected, particularly in mouths with extensive metal [27].

On sloped ridges and in sockets, drill deflection is a physical effect that a robot does not abolish; flattening the entry, starting with a short stiff drill, or using a lateral-cutting pilot remain sensible, and the surgeon should watch for systematic deviation toward the downslope side.

Safety margins from vital structures should not be reduced on the strength of pooled mean deviations. The relevant quantity is an upper percentile of signed deviation toward the structure for the specific system and scenario, which the literature does not yet provide.

For restorative dentists, robotic accuracy supports prefabrication of provisional restorations, with the caveat that depth and rotational position about the implant axis, which determine prosthetic fit with indexed connections, are reported less often than lateral and angular deviation.

10. Technical and Clinical Limitations

The error model assumes small angles, independence of sources, and straight osteotomies. Its numerical illustrations substitute published means for root-mean-square values and use assumed parameters. The review relies on meta-analyses with very high heterogeneity. The phantom protocol removes soft tissue, saliva, limited mouth opening, patient movement, and operator stress, and its bone analogs only approximate drilling behavior; the tool-bone and tracking contributions it measures are therefore lower bounds on their clinical counterparts. Error injection perturbs one source at a time by amounts chosen by the investigators, and the estimated shares depend on the independent estimates of nominal source variances. Access to commercial robotic systems for independent testing, and to their internal calibration parameters for the actuation perturbation, may be restricted by manufacturers. Results apply to the systems and software versions tested. The protocol does not address clinical outcomes, efficiency, cost, or safety events.

11. Proposed Experimental and Clinical Validation

The laboratory program proceeds in four stages. Stage 1 qualifies the reference: the coordinate-measurement chain is characterized and its uncertainty budget documented. Stage 2 comprises the sub-experiments that estimate each source's nominal variance in isolation. Stage 3 is the factorial error-injection study with both reference and conventional evaluation. Stage 4 repeats a reduced design in cadaveric jaws, with reference measurement by an optical or contact coordinate method after dissection, to test whether the phantom ranking of sources holds in tissue.

Clinical validation of the model's main practical prediction, that deviation increases with distance from the fiducials, can be performed on existing data: a multicenter retrospective analysis of robotic cases recording the site-to-splint distance and the signed deviations, with patient-level clustering, reported to STROBE. Prospectively, the evaluation of robotic implant surgery should move to comparative studies with patient-relevant outcomes, complications, prosthetic fit, operative time, and patient-reported measures, in line with the staged framework for surgical innovation [7]; an accuracy advantage that does not translate into any such outcome would not justify the cost. Refutation criteria for H9 and H9b are given in Section 4.

12. Future Research Directions

Three developments follow from the framework. Real-time estimation of target registration error at the planned apex, computed from the fiducial geometry and displayed to the surgeon, would replace an uninformative residual with a relevant quantity; a concept for this is outlined in the appendix. Intraoperative sensing of lateral drill force or deflection would allow tool-bone error to be detected and compensated. And standardized accuracy reporting, signed components in an anatomical frame with stated evaluation uncertainty, would make studies comparable and meta-analysis meaningful; professional bodies or standards committees are the appropriate authors of such a standard. Extension of the error model to curved and long trajectories, as in zygomatic placement, where the angular term dominates, is a natural next step.

13. Evidence-Calibrated Conclusion

Meta-analyses indicate that robot-assisted implant placement achieves lower mean deviations than static or dynamic guidance; the certainty of the comparison is limited by extreme heterogeneity, small developer-led studies, and unquantified evaluation error, and no evidence shows improved patient outcomes. Geometry dictates that, at the angular accuracy reported for robots, apex deviation of conventional-length implants is governed mainly by platform deviation. Registration theory dictates that error at the implant site depends on fiducial configuration and distance in ways that displayed residuals conceal. We hypothesize that the navigation chain, and not the arm, contributes most of the remaining placement variance, and we specify a coordinate-referenced, factorial phantom experiment that can refute this. The numerical examples given are illustrations from published means and assumed values. Until an error budget and outcome trials exist, claims for robotic accuracy should be confined to the surrogate they measure.

Cite this paper

Jain S, Gupta A. Where Does the Error Come From? An Error-Propagation Model for Robot-Assisted Dental Implant Placement and a Coordinate-Measured Phantom Protocol to Apportion Deviation Among Imaging, Registration, Tracking, Actuation, and Tool-Bone Interaction. Working paper. Center for Implant Dentistry; 2026. Available from: https://bayareaimplantdentistry.com/clinician-research-and-publications/error-propagation-in-robotic-implant-surgery

References

  1. Wu Y, Wang F, Fan S, Chow JK. Robotics in Dental Implantology. Oral Maxillofac Surg Clin North Am. 2019;31(3):513-518. doi:10.1016/j.coms.2019.03.013 (opens in a new tab) PMID: 31103316 (opens in a new tab).
  2. van Riet TCT, Chin Jen Sem KTH, Ho JTF, Spijker R, Kober J, de Lange J. Robot technology in dentistry, part two of a systematic review: an overview of initiatives. Dent Mater. 2021;37(8):1227-1236. doi:10.1016/j.dental.2021.06.002 (opens in a new tab) PMID: 34162501 (opens in a new tab).
  3. U.S. Food and Drug Administration. 510(k) premarket notifications K202264, K210711, K211466 and K222049 (Yomi robotic system; Neocis Inc.; K222049 decision date November 4, 2022). Silver Spring (MD): FDA. ‡
  4. Buser D, Martin W, Belser UC. Optimizing esthetics for implant restorations in the anterior maxilla: anatomic and surgical considerations. Int J Oral Maxillofac Implants. 2004;19 Suppl:43-61. PMID: 15635945 (opens in a new tab).
  5. Tahmaseb A, Wu V, Wismeijer D, Coucke W, Evans C. The accuracy of static computer-aided implant surgery: A systematic review and meta-analysis. Clin Oral Implants Res. 2018;29 Suppl 16:416-435. doi:10.1111/clr.13346 (opens in a new tab) PMID: 30328191 (opens in a new tab).
  6. Pimkhaokham A, Jiaranuchart S, Kaboosaya B, Arunjaroensuk S, Subbalekha K, Mattheos N. Can computer-assisted implant surgery improve clinical outcomes and reduce the frequency and intensity of complications in implant dentistry? A critical review. Periodontol 2000. 2022;90(1):197-223. doi:10.1111/prd.12458 (opens in a new tab) PMID: 35924457 (opens in a new tab).
  7. McCulloch P, Altman DG, Campbell WB, Flum DR, Glasziou P, Marshall JC, et al. No surgical innovation without evaluation: the IDEAL recommendations. Lancet. 2009;374(9695):1105-12. doi:10.1016/S0140-6736(09)61116-8 (opens in a new tab) PMID: 19782876 (opens in a new tab).
  8. Van Assche N, Vercruyssen M, Coucke W, Teughels W, Jacobs R, Quirynen M. Accuracy of computer-aided implant placement. Clin Oral Implants Res. 2012;23 Suppl 6:112-23. doi:10.1111/j.1600-0501.2012.02552.x (opens in a new tab) PMID: 23062136 (opens in a new tab).
  9. Schneider D, Marquardt P, Zwahlen M, Jung RE. A systematic review on the accuracy and the clinical outcome of computer-guided template-based implant dentistry. Clin Oral Implants Res. 2009;20 Suppl 4:73-86. doi:10.1111/j.1600-0501.2009.01788.x (opens in a new tab) PMID: 19663953 (opens in a new tab).
  10. Tahmaseb A, Wismeijer D, Coucke W, Derksen W. Computer technology applications in surgical implant dentistry: a systematic review. Int J Oral Maxillofac Implants. 2014;29 Suppl:25-42. doi:10.11607/jomi.2014suppl.g1.2 (opens in a new tab) PMID: 24660188 (opens in a new tab).
  11. Cassetta M, Di Mambro A, Giansanti M, Stefanelli LV, Barbato E. How does an error in positioning the template affect the accuracy of implants inserted using a single fixed mucosa-supported stereolithographic surgical guide? Int J Oral Maxillofac Surg. 2014;43(1):85-92. doi:10.1016/j.ijom.2013.06.012 (opens in a new tab) PMID: 23916310 (opens in a new tab).
  12. Wei SM, Zhu Y, Wei JX, Zhang CN, Shi JY, Lai HC. Accuracy of dynamic navigation in implant surgery: A systematic review and meta-analysis. Clin Oral Implants Res. 2021;32(4):383-393. doi:10.1111/clr.13719 (opens in a new tab) PMID: 33540465 (opens in a new tab).
  13. Jorba-García A, González-Barnadas A, Camps-Font O, Figueiredo R, Valmaseda-Castellón E. Accuracy assessment of dynamic computer-aided implant placement: a systematic review and meta-analysis. Clin Oral Investig. 2021;25(5):2479-2494. doi:10.1007/s00784-021-03833-8 (opens in a new tab) PMID: 33635397 (opens in a new tab).
  14. Block MS, Emery RW, Lank K, Ryan J. Implant Placement Accuracy Using Dynamic Navigation. Int J Oral Maxillofac Implants. 2017;32(1):92-99. doi:10.11607/jomi.5004 (opens in a new tab) PMID: 27643585 (opens in a new tab).
  15. Yang J, Li H. Accuracy assessment of robot-assisted implant surgery in dentistry: A systematic review and meta-analysis. J Prosthet Dent. 2024;132(4):747.e1-747.e15. doi:10.1016/j.prosdent.2023.12.003 (opens in a new tab) PMID: 38195255 (opens in a new tab).
  16. Luo Z, Li A, Unkovskiy A, Li J, Beuer F, Wu Z, et al. Accuracy of robotic computer-assisted implant surgery in clinical studies: a systematic review and meta-analysis. BMC Oral Health. 2025;25(1):540. doi:10.1186/s12903-025-05837-2 (opens in a new tab) PMID: 40217233 (opens in a new tab).
  17. Khaohoen A, Powcharoen W, Sornsuwan T, Chaijareenont P, Rungsiyakull C, Rungsiyakull P. Accuracy of implant placement with computer-aided static, dynamic, and robot-assisted surgery: a systematic review and meta-analysis of clinical trials. BMC Oral Health. 2024;24(1):359. doi:10.1186/s12903-024-04033-y (opens in a new tab) PMID: 38509530 (opens in a new tab).
  18. Bolding SL, Reebye UN. Accuracy of haptic robotic guidance of dental implant surgery for completely edentulous arches. J Prosthet Dent. 2022;128(4):639-647. doi:10.1016/j.prosdent.2020.12.048 (opens in a new tab) PMID: 33678441 (opens in a new tab).
  19. Chen W, Al-Taezi KA, Chu CH, Shen Y, Wu J, Cai K, et al. Accuracy of dental implant placement with a robotic system in partially edentulous patients: A prospective, single-arm clinical trial. Clin Oral Implants Res. 2023;34(7):707-718. doi:10.1111/clr.14083 (opens in a new tab) PMID: 37167364 (opens in a new tab).
  20. Liu Y, Zheng Q, Xu Z, Lin Y, Zhang S, Huang W, et al. Accuracy and operation procedure of robotic computer-aided implant surgery. Sci Rep. 2025;15(1):307. doi:10.1038/s41598-024-83997-x (opens in a new tab) PMID: 39748004 (opens in a new tab).
  21. Fitzpatrick JM, West JB, Maurer CR Jr. Predicting error in rigid-body point-based registration. IEEE Trans Med Imaging. 1998;17(5):694-702. doi:10.1109/42.736021 (opens in a new tab) PMID: 9874293 (opens in a new tab).
  22. Fitzpatrick JM, West JB. The distribution of target registration error in rigid-body point-based registration. IEEE Trans Med Imaging. 2001;20(9):917-27. doi:10.1109/42.952729 (opens in a new tab) PMID: 11585208 (opens in a new tab).
  23. West JB, Maurer CR Jr. Designing optically tracked instruments for image-guided surgery. IEEE Trans Med Imaging. 2004;23(5):533-45. doi:10.1109/tmi.2004.825614 (opens in a new tab) PMID: 15147007 (opens in a new tab).
  24. Widmann G, Stoffner R, Bale R. Errors and error management in image-guided craniomaxillofacial surgery. Oral Surg Oral Med Oral Pathol Oral Radiol Endod. 2009;107(5):701-15. doi:10.1016/j.tripleo.2009.02.011 (opens in a new tab) PMID: 19426922 (opens in a new tab).
  25. Schulze R, Heil U, Gross D, Bruellmann DD, Dranischnikow E, Schwanecke U, et al. Artefacts in CBCT: a review. Dentomaxillofac Radiol. 2011;40(5):265-73. doi:10.1259/dmfr/30642039 (opens in a new tab) PMID: 21697151 (opens in a new tab).
  26. Pauwels R, Araki K, Siewerdsen JH, Thongvigitmanee SS. Technical aspects of dental CBCT: state of the art. Dentomaxillofac Radiol. 2015;44(1):20140224. doi:10.1259/dmfr.20140224 (opens in a new tab) PMID: 25263643 (opens in a new tab).
  27. Flügge T, Derksen W, Te Poel J, Hassan B, Nelson K, Wismeijer D. Registration of cone beam computed tomography data and intraoral surface scans - A prerequisite for guided implant surgery with CAD/CAM drilling guides. Clin Oral Implants Res. 2017;28(9):1113-1118. doi:10.1111/clr.12925 (opens in a new tab) PMID: 27440381 (opens in a new tab).
  28. Joint Committee for Guides in Metrology. Evaluation of measurement data - Guide to the expression of uncertainty in measurement (JCGM 100:2008). Sevres: BIPM; 2008. †
  29. International Organization for Standardization. ISO 5725-1: Accuracy (trueness and precision) of measurement methods and results - Part 1: General principles and definitions. Geneva: ISO. †
  30. Neocis Inc, assignee. Guided dental implantation system and associated device and method. United States patent US 8,808,000 B2 (application filed April 1, 2009). ‡
  31. Neocis Inc, assignee. Surgical robot system for integrated surgical planning and implant preparation, and associated method. United States patent US 10,660,706. ‡
  32. Neocis Inc, assignee. Tracking and guidance arrangement for a surgical robot system and related method. United States patent application publication US 2018/0078332 A1. ‡
  33. Biomet 3i LLC, assignee. Robotic device for dental surgery. United States patent US 10,959,814 B2. ‡
  34. Biomet 3i LLC, assignee. Robotic device for dental surgery. United States patent US 10,905,504 B2. ‡
  35. U.S. Code of Federal Regulations. Title 21, Section 872.4120: Bone cutting instrument and accessories (product code PLV as applied to dental stereotaxic instruments). Washington (DC): U.S. Government Publishing Office. ‡
  36. Reference verification note. 26 of 35 references are PubMed-indexed; their bibliographic records (authors, title, journal, year, volume, pages, DOI, PMID) were retrieved programmatically from the PubMed database on November 17, 2026. ‡ Standard, regulatory record or patent whose identifying details were confirmed against the issuing body’s public record during the research phase. † Source not indexed in PubMed (book, standard, guidance or non-indexed journal); bibliographic details are cited from the published record and were not database-verified in this drafting session. Database retrieval confirms that each record exists as cited; it does not replace full-text reading by the responsible authors of every statement attributed to a source.